Axles & drive shafts

1:10 XS Dog Bone Rear, spare part drivetrain

€17.79

The dog bone shaft is a core link in many RC drivetrains, carrying power from the differential to the wheel side while allowing the suspension to move. This 1:10 XS Dog bone rear set includes 2 rear drivetrain shafts for compatible Carson XS-Chassis vehicles and is intended as a dedicated spare part for maintenance or repair. The set is specified for the Carson XS-Chassis platform and matches the listed models 500404252, 500404253, 500404254 and 500404255, as well as 500404360, 500404361, 500404362 and 500404363. In the range, these references cover Stadium Fighter, Offroad Fighter Cage, Tekuro and Ryken versions. The dogbone layout uses rounded ends with cross pins to sit in the drive cups and transmit rotational force even as the rear suspension geometry changes during running. The black metal parts shown are shaped for drivetrain duty and suit workshop stock for regular wear replacement. As a rear axle spare part, this set fits hobby use where a compatible chassis is already in service and the drivetrain needs a fresh mechanical link after heavy off-road sessions or routine upkeep. Age marking: 14 years.

Axles & drive shafts

Akuma Alu-hex Hub 17 mm RC Wheel Adapter

€12.79

The Akuma Alu-hex hub 17 mm is a compact RC spare part set for wheel mounting and running gear service on compatible Akuma model vehicles. With 2 machined aluminium hub pieces, 2 matching nuts, 2 metal pins and 2 black set screws, the set brings together the fastening hardware needed for a complete hub replacement at the wheel end. The 17 mm hex format defines the wheel interface, while the threaded hub design and separate locking hardware point to a mechanical assembly that is secured in several steps rather than a simple push fit. The metal pins and set screws support alignment and retention within the hub setup, helping restore the intended connection between axle area and wheel mount when original parts are worn, lost or damaged. The silver finish keeps the parts easy to identify during bench work, and the compact format suits parts storage in an RC workshop or field box. This kind of hardware fits naturally into rebuilds, maintenance sessions and spare-parts stock for regular RC driving. Whether a model is being refreshed after heavy use or prepared with replacement wheel-end hardware before the next run, this set supplies the core mounting parts in one pack.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Center Differential 46T, RC spare part

€41.99

A center differential sits at the heart of an RC drivetrain, balancing power flow between the front and rear sections as the model accelerates, brakes and changes direction. This complete 46T assembly is designed as a direct spare part for selected Carson platforms, giving model-building enthusiasts a defined replacement for the center transmission area. The unit combines a differential housing, a 46-tooth ring gear, output cups and collars in one assembled component. That complete format matters when an existing drivetrain part shows wear, because the replacement can focus on the full center diff rather than on separate small parts. The gear assembly is intended for Carson Virus 4.0, 4.1, 4.2, 4.3 and Race models, and it also fits Akuma versions named in the product data. Within those platforms, the center differential helps distribute rotational force through the drivetrain while allowing the front and rear ends to turn at different rates when the running surface changes. In workshop use, this kind of spare part supports maintenance after heavy running sessions, drivetrain servicing or a rebuild of the center transmission section. The 14 Years age marking is stated in the product data. For hobby benches focused on keeping a Virus or Akuma model ready for the next outing, a model-specific center differential like this keeps the replacement process tied to the intended vehicle family.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Center Drive Shafts, RC spare part, 2 pcs

€16.79

Center Drive Shafts, 2 pcs. is a dedicated RC spare part set for compatible Carson Virus and Akuma vehicles. The set contains 2 centre drive shafts and is intended for drivetrain service on models where the original shafts need replacement after regular use. Compatibility is clearly defined for Virus 4.0, 4.1, 4.2, 4.3 and Race versions, covering the model numbers 500409050, 500409051, 500409060, 500409061, 500409067, 500409068, 500409080, 500409081, 500409086 and 500409087. It also fits Akuma models 500409082 and 500409083. The image shows 2 black shaft components in different lengths, each with rounded ball ends and metal pins, a layout suited to the connection points used in RC drivetrain assemblies. For hobby workbench maintenance, a model-specific spare part saves guesswork during service and supports a clean replacement process in the centre drivetrain area. Age marking: 14 years. No batteries are included.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Drakuro Center Driveshaft, RC spare part

€6.49

The Drakuro Center driveshaft short is a dedicated RC spare part for the drivetrain of a 1:8 4WD chassis. With its specified 55 mm length, it is intended for the matching center shaft position in the Carson Drakuro layout, where accurate fit matters for the connection between drivetrain components. In a running model, the center driveshaft links key transmission sections and passes drive through the chassis as the power system works under load. Replacing a worn or damaged shaft with the correct version helps keep the drivetrain layout consistent and avoids guesswork during maintenance. The part is listed in the Drakuro range context alongside the BL 3S vehicle variants, which makes it a useful reference component for repairs within that platform. On the workbench, this spare part suits routine servicing, targeted replacement and rebuild jobs where the exact shaft length is needed. It fits naturally into workshop stock for hobbyists maintaining a 1:8 4WD RC vehicle and looking for the correct Drakuro transmission component.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Drakuro Center Driveshaft, RC spare part

€10.49

The Drakuro Center driveshaft long is a dedicated RC spare part for the drivetrain of the Carson Drakuro BL 3S platform. With a length of 142 mm, it is specified for the long center shaft position in the compatible 1:8 4WD chassis and gives model-building enthusiasts a clearly defined replacement for maintenance and repair. Within a 4WD layout, the center driveshaft forms part of the connection between major drivetrain sections, making correct fit and matching length essential when worn transmission parts are replaced. This version is assigned to Carson model numbers 500409096 Drakuro BL 3S Anthracite/Red and 500409097 Drakuro BL 3S Blue, which keeps compatibility clear when servicing the chassis. The part is intended for model supplies and workshop use rather than as a general universal shaft, so the stated 142 mm dimension is the key reference for selection. It fits routine repair work after drivetrain wear, as well as planned parts stocking for an existing Drakuro BL 3S. In a hobby workshop, a model-specific replacement like this helps return a 1:8 4WD chassis to its intended running condition with the correct shaft format for the designated position.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Drakuro Drive Cups, RC spare part, 1:8 4WD

€12.99

This Drakuro Drive Cups set is a dedicated RC spare part for the centre driveshaft on the 1:8 4WD chassis named in the product data. Supplied as 2 pieces, it is intended for the front and rear positions where the centre driveshaft connects into the drivetrain layout. The set is listed for the Carson Drakuro BL 3S variants 500409096 in anthracite red and 500409097 in blue, which gives model-building enthusiasts a clear chassis reference when selecting replacement parts. Rather than covering a broad range of unrelated fittings, this spare focuses on one defined transmission component group. That makes parts planning more straightforward during routine maintenance, wear replacement, or a targeted drivetrain refresh on the specified platform. In the workshop, dedicated replacement parts help keep servicing organised around the exact chassis architecture already in use. For rebuilds after heavy running sessions or for keeping spares ready between maintenance intervals, these 2 drive cups fit naturally into a parts box built around the Drakuro 1:8 4WD range.  Warning! Not suitable for children under 14 years.

Additional spares

Drakuro Lower Inner Arm Hinge Pins, RC spare part

€6.49

These lower inner arm hinge pins are a dedicated spare for the Drakuro platform and address a precise chassis connection point rather than a general hardware need. With a specified length of 70 mm and a pack of 2 pieces, the set is intended for the lower control arm retaining position on the 1:8 4WD chassis used by the named Drakuro BL 3S models. In regular RC maintenance, suspension hardware needs the right dimensions and the right fit at the right mounting point. This set keeps that replacement specific: lower inner arm hinge pins for the chassis area named in the data, sized at 70 mm, and supplied as 2 matching pieces for the same suspension location. The reference to Drakuro BL 3S anthracite/red and Drakuro BL 3S blue ties the spare to the stated vehicle variants, which helps when checking compatibility within the range. Whether the chassis is being serviced after repeated track sessions or refreshed as part of a parts stock for the workshop, these pins support a straightforward replacement at the lower inner arm position. The focused specification makes them a useful choice when the goal is to keep a Drakuro 1:8 4WD chassis running with the correct suspension hardware.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Drakuro Rear Driveshafts, RC spare part, 85 mm

€12.99

Rear driveshafts take a constant load in a 1:8 4WD chassis, linking the drivetrain to the rear wheels through every acceleration, braking phase and direction change. This set provides 2 replacement rear driveshafts in 85 mm for the Carson Drakuro BL 3S, giving the rear driveline the specified part length for a correct match on the named platform. The set is intended for the Carson Drakuro BL 3S in the anthracite/red version with Material No. 500409096 and the blue version with Material No. 500409097. As dedicated spare parts for the rear axle area, the shafts are suited to maintenance work when worn or damaged driveline parts need to be exchanged. The 85 mm dimension is the key fit detail here, because driveshaft length must match the chassis layout and suspension geometry of the specified model. With 2 pieces in the pack, both rear sides can be equipped in one repair step where the model requires a pair. In workshop use, this kind of replacement part supports routine servicing after repeated running sessions on a Drakuro BL 3S chassis. It also suits a planned rebuild in which the rear drivetrain is being refreshed with model-specific spare parts rather than generic alternatives.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Drakuro Stabilizer Set, chassis accessory, 1:8

€10.49

Built for the Drakuro platform, this front and rear stabilizer set adds a targeted chassis upgrade for the 1:8 4WD layout. The set is assigned to the Drakuro BL 3S versions 500409096 in Anthracite/Red and 500409097 in Blue, giving model-building enthusiasts a model-specific route when refining the running gear. Stabilizers work through the suspension movement across each axle, linking left and right sides to influence how the chassis reacts when cornering forces build. With front and rear parts supplied for the same vehicle family, setup changes can be approached as a balanced package rather than as a single-end modification. That makes the set relevant for rebuilds after wear, for planned tuning sessions, or for restoring the intended hardware on an existing Drakuro chassis. As an accessory in the Models & Accessories range, it focuses on the mechanical side of RC handling rather than cosmetic changes. The set fits naturally into bench work before the next run, especially when a 1:8 4WD model is being refreshed or adjusted for a different handling feel. It also suits spare-parts storage for the named Drakuro BL 3S versions, keeping the correct stabilizer hardware ready for future chassis work.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Drakuro Steering Link Set, model accessory

€6.49

A steering system only feels right when the linkage matches the chassis it was made for. This Drakuro Steering link set is specified for the 1:8 4WD chassis and gives model-building enthusiasts a dedicated replacement option for the steering setup on compatible Drakuro vehicles. The set is listed as a model accessory in the Models & Accessories range and is assigned to the Drakuro BL 3S platform. Compatibility is stated for 500409096 Drakuro BL 3S Anthracite/Red and 500409097 Drakuro BL 3S Blue, which makes the intended fit easy to identify when planning maintenance or keeping workshop spares ready. As a steering link set, it belongs to the front-end control hardware that connects steering movement through the chassis layout, making it a relevant part for repair work after wear or damage. The focus here is not on a generic spare, but on a named set for a defined vehicle platform. In workshop use, this kind of chassis-specific linkage helps keep servicing organised and avoids guesswork when replacing worn steering parts on a compatible 1:8 4WD model. It suits routine upkeep, targeted repairs, and parts storage alongside other Drakuro running gear components.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Front Universal Drive Shafts, RC spare part

€29.99

Front universal drive shafts are a focused drivetrain replacement for Carson Virus and Akuma model platforms, supplied as 2 matching parts for the front axle assembly. The black metal construction and universal-joint style ends suit the mechanical demands of rotational power transfer where steering angle and suspension movement both need to be accommodated within the same front drivetrain area. The shaft design shown in the set combines a long rod section with a cylindrical housing, external threads near one end and a cross-drilled connector section for installation in the relevant drivetrain assembly. At the opposite end, the rounded joint section with 2 perpendicular pins forms the coupling point that allows the shaft to transmit drive while the front end geometry continues to move through use. Compatibility is stated for Virus 4.0, 4.1, 4.2, 4.3 and Race, as well as Akuma, making the set a clear match for maintenance, repair or parts replacement on those series. In workshop use, a matched 2-piece shaft set helps restore the front drive path on models that show wear, impact damage or drivetrain play at the axle end. Age marking: 14 years.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

KoD Front Drive Shafts, RC spare part

€28.99

KoD Front drive shafts are a dedicated 2-piece spare set for the front drivetrain of a compatible KoD model. Each shaft is shown in black metal and uses a jointed layout with visible cross pins at the upper end, giving the assembly the articulated connection needed in a driven front axle. The shape of each component combines a long slim shaft section, a rounded joint head and a wider cup-style lower housing. That geometry suits the changing angles that occur at the front end of an RC vehicle while drive is being transmitted to the axle. As replacement parts, the pair provides matching components for the left and right side rather than a mixed assortment. The metal build adds a precise mechanical character that fits the role of drivetrain hardware. In workshop use, these shafts suit maintenance, repair or the refresh of a worn front drive assembly on a 14 Years+ model. The set is focused on one clear task: replacing the front axle shafts with the correct 2 matching components so the drivetrain can be reassembled with the intended part type.

Axles & drive shafts

KoD Rear Hub Carrier, RC spare part, 2-piece

€12.79

The KoD Rear Hub Carrier set supplies 2 mirrored replacement parts for RC model maintenance, with one left-hand carrier and one right-hand carrier identified by L and R markings on the moulding. Each carrier shows a large circular opening in the lower section, an upper forked slot, and inward-facing tabs with screw holes that define its mounting position within the rear wheel-related assembly. This layout makes the set a focused spare part for restoring the original rear mounting geometry when worn or damaged carriers need replacement. The mirrored construction matters during fitting because the left and right pieces are not interchangeable, and the marked orientation helps keep the assembly sequence clear on the bench. The black moulded form is shaped for symmetrical installation, so both sides of the rear assembly can be renewed together with matching parts rather than mixing old and new carriers. In workshop use, the set suits routine servicing, rebuilds after heavy running, or keeping key spares ready between track sessions. Age marking: 14 Years. Batteries are not included.

Axles & drive shafts

KoD Upright Holder Set Front RC Spare Parts

€12.79

The KoD Upright holder set front is a dedicated front-end spare parts set for RC model maintenance, built around 2 mirrored holders marked L and R. Each holder combines a large circular hub opening with angular side sections and a long curved arm, creating the defined mounting shape needed at the front of the model. The set also includes 4 screws and 4 metal rings, providing the matching small hardware shown for installation. This layout suits repair work where the original front holders are worn, damaged or missing, and it keeps both sides of the assembly aligned with corresponding left and right parts rather than a universal single shape. The black moulded pieces are formed with integrated arms instead of separate add-on sections, which helps preserve the intended geometry of the front suspension or steering area during replacement. In workshop use, the paired design supports a straightforward side-by-side swap on the front axle area, with each marked part assigned to its correct position. For hobby benches stocked with RC maintenance parts, this set adds a model-specific solution for restoring the front mounting structure with the included fastening hardware.

Axles & drive shafts

KoD Upright Set Front, RC spare part pair

€12.79

The KoD Upright set front includes 2 black mirrored components shaped for the front end of an RC model, with a large central circular opening and several defined mounting points that indicate their role within the steering or suspension assembly. As a matched left and right pair, the set supports a consistent replacement setup when the original front uprights need to be swapped during maintenance. Each part shows a technical layout with upper cylindrical mounts, a lower forked section and small attachment holes that help position the component within the surrounding front-end hardware. This kind of spare part is useful when a rebuild calls for accurate mirrored geometry rather than mixing unmatched pieces. The 2-piece format also keeps both sides of the front assembly aligned to the same component version, which matters when restoring worn running gear on an RC vehicle. On the workbench, the set fits naturally into repair, servicing and parts organisation for hobby-grade RC models. Whether replacing damaged front-end hardware after running sessions or refreshing an older build, the KoD Upright set front adds a clearly defined pair of structural components to the spares box.

Axles & drive shafts

Rear Drive Shafts, RC spare part, 2-piece set

€16.79

Rear drive shafts are a core wear part in RC vehicle drivetrains, and this 2-piece set is made to replace the rear dog bone shafts used in selected Carson models. The black metal shafts use a straight centre section with rounded ends and cross pins, a layout commonly used to transmit drive through moving suspension travel while keeping the rear axle connected under running loads. The set is specified for Virus 4.0, 4.1, 4.2, 4.3 and Race variants, and it is also listed for Akuma references in the provided data. As a dedicated spare part, it supports targeted servicing of the rear drivetrain instead of replacing a larger assembly. The 2 included shafts suit the rear position named in the designation, making the set relevant for repair after wear, impact or lost drivetrain engagement. The dog bone format also makes the function easy to identify during workshop maintenance on compatible chassis. In hobby use, replacement shafts like these help return an RC vehicle to consistent running after drivetrain damage or heavy use on track and off-road surfaces. Age marking: 14 years. Before fitting, compatibility should be checked against the listed model references in the product data.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Rear Hub Carrier, XS-Chassis spare part 1:10

€6.89

The rear hub carrier set is made for 1:10 Carson XS-Chassis vehicles and supplies 2 matching replacement parts for the rear upright area. Each moulded component is shaped to sit at the wheel end of the chassis, where the bearing seat, forked arms and fastening points connect the rotating axle assembly with the surrounding suspension hardware. Compatibility is clearly defined for Carson XS-Chassis references 500404252, 500404253, 500404254 and 500404255. That covers the Stadium Fighter in blue and orange as well as the Offroad Fighter Cage in turquoise and red. The pair format suits left and right replacement in one step, which helps keep the rear end layout consistent when a full side-to-side exchange is needed after wear, damage or a rebuild. In workshop use, parts like these matter where clean fit and correct mounting geometry decide how smoothly the rear assembly goes together. The compact shape and dedicated mounting points make this set a practical choice for maintenance, repair stock or a chassis refresh on the listed XS-Chassis models.

Axles & drive shafts

Rear Hub Carriers, RC spare part, 2-piece set

€12.79

Rear hub carriers are small parts with a big role in the running accuracy of an RC chassis. This 2-piece set is made for the rear axle area of selected Carson models and provides the matched carrier shape needed for a precise replacement when the original parts are worn, damaged or missing. The set is specified for Virus 4.0, 4.1, 4.2, 4.3 and Race versions, and it also fits the listed Akuma models. Each carrier is formed as a dedicated chassis component with a circular centre section, forked mounting arms and additional fastening holes on the side tab. That layout supports the connection of the surrounding rear suspension hardware and keeps the mounting points in the correct position within the assembly. As a spare part, the pair is suited to maintenance, repair work and the careful rebuild of an existing vehicle rather than a general universal application. In the workshop, a matched left and right pair helps bring a used model back into running condition with the correct rear carrier format for the compatible platform. The age marking in the product data is 14 years and up.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Rear Wheel Axles, RC spare part, 2 pcs

€8.49

Rear Wheel Axles, 2 pcs. is a dedicated RC spare part set for compatible Carson Modelsport vehicles, built for rear drivetrain maintenance on selected Virus and Akuma models. The set contains 2 matching axle components and is intended for the rear position, where the specified fit matters for a clean replacement during service or repair work. The compatibility data covers Virus 4.0, 4.1, 4.2, 4.3 and Race variants, along with listed Akuma versions, so the set can be matched to the correct platform before installation. The parts shown are dark metal drivetrain components with cylindrical shafts, cross holes and cup-shaped ends, a form used for pinned mechanical connections inside an RC drive assembly. That shape supports integration with the surrounding rear transmission hardware rather than acting as a universal axle for unrelated models. Age marking: 14 Years. In workshop use, a dedicated spare set like this helps restore the intended rear drive connection after wear or damage on a compatible chassis. For hobby benches that stay organised by model family, the clearly defined Virus and Akuma fitment keeps replacement planning straightforward when rear axle parts are needed.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Steering Link Set, RC spare part for Virus

€6.49

The Steering Link Set is a dedicated RC spare part for Carson Virus and Akuma platforms, made to restore the steering mechanism with a matching replacement when the original linkage needs changing. It covers a broad group of compatible models, including Virus 4.0, 4.1, 4.2, 4.3 and Race versions, making it a practical workshop part for regular servicing. Compatibility in the product data extends across the model numbers 500409050, 500409051, 500409060, 500409061, 500409067, 500409068, 500409080, 500409081, 500409086 and 500409087, as well as Akuma references 500409082 and 500409083. That range helps keep maintenance focused on the correct platform instead of relying on generic linkage parts. As a steering link set, it belongs to the control hardware that connects steering movement within the vehicle, so it supports the return of the intended steering function on the listed models. In the workshop, this kind of replacement part suits routine repairs after wear, damage or play in the steering assembly. The product data states an age marking of 14 Years. No batteries are included.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Universal Drive shaft, RC spare part for 1:10

€17.79

Built for the front axle area of Carson 1:10 XS-Chassis vehicles, this Universal Drive shaft set includes 2 matching shafts for drivetrain service and replacement. The black metal parts use a slender shaft body with shaped connection ends, including a ball-style end with cross pin and a stepped opposite end, for the mechanical link between drivetrain components at the front. The set is intended for several XS-Chassis based models and is listed for 500404252, 500404253, 500404254, 500404255, 500404360, 500404361, 500404362 and 500404363. That covers Stadium Fighter in blue and orange, Offroad Fighter Cage in turquoise and red, plus Tekuro in grey green and grey blue and Ryken in blue and green. As a dedicated RC spare part, the pair suits workshop stock, routine maintenance and the replacement of worn front drivetrain hardware on compatible chassis. For model-building enthusiasts, parts like these keep a favourite vehicle mechanically complete between running sessions and repair work. The 2-piece format provides the matching left and right front shaft components needed for the specified XS-Chassis applications.

Axles & drive shafts

Virus 4.0 Dog Bone Center, spare part set

€16.79

The Virus 4.0 uses a center dog bone layout to pass drive through the middle of the vehicle, and this 2-piece replacement set is made for exactly that task. With 2 matching center shafts in the pack, the spare set gives model-building enthusiasts the correct component group for targeted drivetrain maintenance on the Virus 4.0. The straight shaft form, rounded end sections and connector pins match the classic dog bone mechanism used in RC vehicle drivetrains, where the shaft sits between connected drive elements and transmits rotation through the center section. That makes this set relevant when the original center dog bone parts show wear, damage or loss during running or workshop service. As a dedicated spare part rather than a universal rod, it stays focused on the named Virus 4.0 application and avoids guesswork over the part type needed for the repair. On the bench, the 2 matching pieces suit planned servicing as well as direct replacement of the paired center components. In an active RC model collection, keeping the correct drivetrain spares ready helps return the Virus 4.0 to running condition with the intended center dog bone format.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus 4.0 Middle Diff Complete Drivetrain Part

€41.99

The Virus 4.0 Middle Diff complete is a drivetrain spare part built for the centre section of the Virus 4.0. Its assembled layout combines a central differential housing, a mounted gear ring and output shafts in one unit, giving model-building enthusiasts a direct replacement for a key transmission component. The dark cylindrical body forms the core of the assembly, while the toothed gear around the centre engages with the surrounding transmission to carry rotational input onward through the driveline. Polished metal contact surfaces at both ends mark the running points of the unit, and the two different shaft terminations show how the assembly connects into the existing mechanical layout. One side uses a forked output end, while the opposite side carries a squared drive connection, so the part is shaped for a defined position within the drivetrain rather than as a generic gear set. In workshop use, this complete differential unit supports repair jobs, routine maintenance and parts replacement on the Virus 4.0 platform. The preassembled format keeps the focus on fitting the correct centre drivetrain component and getting the model's transmission system back into working order with a matching spare part.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus Akuma Differential, RC drivetrain spare part

€41.99

A differential is one of the key drivetrain parts in an RC vehicle, balancing power transfer with the different wheel speeds needed in a turn. This Virus Akuma differential is designed for front or rear installation, making it a practical spare part for compatible Carson models when a worn drivetrain unit needs replacement. The assembly uses a large geared ring around the differential housing to pass drive through the axle system, while the side outputs connect into the vehicle drivetrain. That mechanism allows the left and right wheels on the same axle to rotate at different speeds instead of forcing both to turn identically. In use, that helps the model track more cleanly through bends and keeps the drivetrain working as intended after servicing. The compact construction also suits routine maintenance benches, rebuild projects and targeted repairs where the original drivetrain layout needs to be retained. Compatibility covers the Virus 4.0, 4.1, 4.2, 4.3 and Virus Race series as well as Akuma models listed in the technical data. With the age marking of 14 years and up, the part fits the hobby-focused character of RC workshop care, whether the task is replacing a damaged unit or refreshing a heavily used axle drive.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus-Ex Center Drive Shaft, spare part

€16.79

The Virus-Ex Center drive shaft is a dedicated spare part for the Carson Modelsport Virus-Ex range and focuses on a core point in the drivetrain layout. As a center drive shaft, it is intended for the mechanical link between drivetrain sections, making it a relevant replacement when wear, damage, or maintenance work calls for the original part to be exchanged. The supplied image shows 2 matching shaft pieces in black metal, each built with a straight cylindrical body and rounded end sections with protruding metal pins. That construction points to a part designed to connect into the designated mounting points of the model's transmission system rather than serving as a universal accessory. For hobbyists working on repair or upkeep, a model-specific spare part like this helps keep the drivetrain layout consistent with the intended Virus-Ex configuration. The 14 Years age marking is stated in the product data. On the workbench, this kind of replacement part fits routine service jobs, rebuilds after heavy running, or the refresh of a used chassis. The compact format also makes it a practical addition to a spares box for regular maintenance of the matching Virus-Ex model.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus-Ex Front Drive Shafts, RC spare parts

€28.99

The Virus-Ex front drive shafts are a matched 2-piece spare set for the front drivetrain of the model. Each shaft uses a slim black metal body, a cylindrical cup section with visible grooves, and a rounded ball end with 2 cross pins to connect the driven front axle components. As replacement parts, these shafts focus on a core mechanical job: transmitting drive from the differential side to the front wheels while allowing the front assembly to keep its intended movement. The visible joint layout gives model builders a clear indication of where each part works within the axle system. The pair format suits left and right front-side service in one pack, so worn or damaged original shafts can be exchanged with matching components. The black finish and machined form keep the emphasis on fit and drivetrain function rather than cosmetic add-ons. In workshop use, the set supports routine maintenance, repair after heavy running sessions, or the refresh of a front-end drivetrain that no longer runs cleanly. For hobby benches stocked with Virus-Ex spares, these 2 shafts add a model-specific replacement part for keeping the front drive system complete.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus-Ex rear axles, RC spare parts

€8.49

The Virus-Ex rear axles are a model-specific drivetrain replacement set for RC maintenance, supplied as 2 matching black metal parts. Each axle shows a cylindrical shaft with a cross-drilled hole near the lower section and a forked cup-shaped top with a vertical U-shaped slot, a geometry made to link into the rear drive assembly with the correct mechanical interface. As a spare part for the Virus-Ex, this set focuses on the rear transmission area where accurate fit matters for dependable power transfer. The machined openings support pin-based fastening, while the cup form is built to accept the matching drivetrain connection used at the rear of the model. The paired format provides the left and right rear pieces together, which helps keep replacement work consistent across the axle set. Black metal construction suits the demands of a loaded drivetrain section where rotating parts and repeated connection points call for a solid material choice. In workshop use, these rear axles fit naturally into routine servicing after wear, damage or a stripped rear drive connection appears. They also make sense as shelf stock in an RC spares collection, ready for rebuilds, repairs and planned maintenance on the Virus-Ex platform.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus-Ex Steering linkage, spare part, 2-piece

€9.79

Small steering parts make a clear difference once the front end needs a clean mechanical connection again. This Virus-Ex Steering linkage set includes 2 matching linkage parts designed as replacement components for the steering assembly, with an eyelet on one end and a socket-style opening on the other. The shape suits the job of linking rods or matching steering hardware within the mechanism, so worn connectors can be exchanged with parts intended for the same layout. The black moulded pieces use a narrowed centre section between the mounting points, keeping the form compact while preserving the defined connection geometry. Because this set is a dedicated spare part for the Virus-Ex, it fits naturally into routine maintenance, rebuilds and parts storage for an existing model. The pack count of 2 also suits repairs where both sides of a linkage pair are replaced together. On the workbench, these connectors belong in the small but essential group of parts that restore proper steering movement after wear or damage. For model hobbyists maintaining a Virus-Ex, the set adds the correct replacement pieces for service work, rebuild sessions or keeping spares ready between runs.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus-Ex Steering Set, spare part for RC models

€12.69

The Virus-Ex Steering Set (2) is a dedicated spare part for the steering area of a Virus-Ex RC model, supplying 2 matching components for repair or planned maintenance. The black moulded parts are shaped for mechanical connection points, making them suitable for restoring movement where the steering linkage needs fresh hardware. Their form points to pivot and mounting functions within the front-end assembly, with openings and joint sections designed to connect into the steering mechanism rather than serving as decorative trim. As a model supply, this set fits the practical side of the hobby bench: replacing a stressed steering part can help return the chassis to controlled directional input after wear, impact, or repeated running. The pack count of 2 supports work on paired or matching positions where the mechanism calls for corresponding pieces. With the age marking of 14 Years in the product data, the set sits in the enthusiast segment of RC maintenance and parts management. It suits workshop use alongside routine inspection of linkages, mounts, and moving front-end hardware, especially when a Virus-Ex build is being kept ready for the next session.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus-Ex Steering-link, steering linkage

€6.39

The Virus-Ex Steering-link focuses on a small but decisive part of an RC model's steering system: the mechanical connection that transfers servo movement into directional change at the front end. A threaded metal linkage rod, rod ends and a servo arm form an adjustable assembly that suits detailed workshop maintenance on Virus-Ex models. At the centre of the rod, a hex adjustment section allows the linkage length to be altered directly on the part. That makes it possible to correct steering alignment and refine the relationship between servo travel and steering movement without changing the whole assembly. The ball-joint style connection points add the pivoting freedom needed where the linkage moves through changing angles. This combination of threaded adjustment, metal rod construction and articulated end points gives the steering mechanism the functional detail expected in hobby-grade RC maintenance. As a replacement set, this steering-link fits naturally into routine servicing after wear, impact or drivetrain and chassis work that affects steering setup. The compact parts are aimed at model-building enthusiasts who value direct mechanical tuning and a clean, responsive linkage path in the workshop and on the track.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus/Akuma Steering Set, spare part, 2 pcs

€12.79

The Virus and Akuma platforms are built around serviceable component groups, and this steering set supplies 2 dedicated replacement parts for that exact area. The black moulded pieces are shaped with multiple openings, sockets and mounting points that match their mechanical role inside the steering assembly. One part carries a larger central circular opening with additional side openings, while the second part forms the matching counterpart with rounded ends and a recessed central channel. That geometry matters during maintenance because the steering mechanism depends on correctly matched connection points rather than generic hardware. As a spare part, this set is intended for targeted replacement when the original steering components are worn, damaged or missing. The 2-piece format keeps the relevant pair together for workshop stock and repair planning. In practical use, the set suits bench repairs, routine maintenance and the refresh of an existing Virus or Akuma model after heavy running sessions. For hobbyists working on compatible Carson Modelsport vehicles, a dedicated steering replacement set helps return the assembly to its intended mechanical layout with the correct parts on hand.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

X 10 EB Dirtwarrior Turnbuckle Set, RC spare part

€12.99

The X 10 EB DIRTWARRIOR Full Turnbuckle Set brings adjustable linkage hardware to the workbench for maintenance, repair and chassis tuning on the matching model. With 7 pieces in the set, it covers key connection points where threaded links and rod ends are used to set geometry and restore precise movement. The visible metal turnbuckles use threaded ends so link length can be altered without replacing the whole assembly, a practical detail when steering alignment or suspension settings need correction after wear or impact. Black rod ends form the pivoting connection at each end of the linkage and pair with the turnbuckles to create adjustable assemblies for control and setup work. The set also includes matching hardware components for mounting and rebuilding these connections, making it useful when original parts are bent, worn or missing. As a model spare part rather than a general accessory, it is shaped around the X10EB application named in the data. On an RC hobby bench, this kind of hardware supports routine servicing after running sessions, rebuilds following contact on loose terrain, or setup changes before the next outing. Age marking: 14 years and up.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

X-Crawlee Pro Linkage Set, model accessory

€36.49

The X-Crawlee Pro Linkage Set brings 10 replacement linkage bars into the workshop for RC maintenance on the matching model. Blue metal rods and black eyelet end pieces give each part a clear technical layout, with mounting holes that suit connected moving sections where a link needs to be renewed. The set image shows several lengths, so the pack covers different connection positions rather than repeating a single rod size throughout. Most bars use ring-style ends on both sides, while one part features a different flat-ended connector, adding another fitting style within the 10-piece assortment. That mix supports repairs on linkage points that do not share the same geometry. As a model accessory for the X-Crawlee Pro, the set focuses on the mechanical connections that guide motion between mounted components. In a hobby bench setup, these rods fit naturally into regular servicing, rebuilds or replacement work after heavy running. The 14 Years age marking places the set in the hobby segment, where model builders often keep key spare parts ready for maintenance sessions and setup changes.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

X10EB Steering Block, RC spare part, front

€20.99

The X10EB Steering Block front is a dedicated RC spare part for the front wheel assembly, built around mirrored upright components and matching carrier pieces for the hub area. The black moulded parts form the mounting point for steering and suspension connections, giving the axle section the correct structure for repair or replacement work. A large central opening in each upright supports the bearing seat, while the included ball studs create the connection points for the steering linkage. The set also contains larger pivot hardware for the kingpin area, plus small washers, spacers and O-rings that belong to the assembly itself. This combination suits maintenance work where worn or damaged front-end parts need to be exchanged with matching components rather than mixed hardware. The front-specific layout keeps the geometry focused on the X10EB axle section named in the data. On the workbench, the set supports a focused rebuild of the knuckle and hub area with the small fitting parts already grouped together. For RC hobbyists running the X10EB, it provides the key pieces needed to restore the steering block section and return the front assembly to service.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

XL Drive shaft, model accessory, steel center

€8.99

A center drive shaft is one of the key links in an RC drivetrain, carrying power between major transmission components as the model runs. This version is specified as a steel center drive shaft for the 1:10 XL chassis, giving model-building enthusiasts a clearly defined spare part for maintenance, repair or a planned rebuild. The product data identifies this part as an XL Drive shaft and places it within models and accessories, with steel named as the material and the 1:10 XL chassis stated in the technical text. That combination makes its role clear: it is a dedicated drivetrain component rather than a general workshop part. In practical use, a center shaft replaces a worn or damaged link in the transmission path and helps return the chassis to proper mechanical operation. The steel construction is the concrete material detail given for this component, while the chassis reference provides the essential fit context for parts planning. On the bench, this kind of spare is useful during routine servicing, fault finding after drivetrain wear, or when keeping a compatible RC model ready for the next running session. The age marking in the data is 14 Years, and batteries are not included.

Axles & drive shafts

XS Servo Saver Set, RC spare part for 1:10

€13.49

The XS Servo Saver set brings together a servo saver, steering plate and post as a dedicated spare-parts package for 1:10 XS-Chassis models. In the workshop, that combination targets the steering area directly and gives model-building enthusiasts the exact component group named in the data for a focused replacement task. Compatibility is stated for the XS-Chassis references 500404252, 500404253, 500404254 and 500404255, and the short advertising text also lists 500404360, 500404361, 500404362 and 500404363. The BasicText names the related vehicle designations Stadium Fighter blue, Stadium Fighter orange, Offroad Fighter Cage turquoise, Offroad Fighter Cage red, Tekuro grey green, Tekuro grey blue, Ryken blue and Ryken green. As a model supply in the Models & Accessories range, this set suits maintenance work where the steering mechanism needs the specified replacement parts rather than a general universal component. Age marking in the data is 14 Years. On the bench, the set fits neatly into repair, upkeep and parts sorting for compatible XS-Chassis vehicles, whether the goal is returning a runner to service or keeping a matching spare set ready for the next steering rebuild.

Axles & drive shafts

XS Upright Set Front, RC spare part for 1:10

€8.99

The XS Upright Set Front is a dedicated RC spare part for the Carson XS-Chassis in 1:10 scale. With 2 uprights and 2 holders, the set is intended for the front section of compatible chassis versions and gives model-building enthusiasts the exact component group needed when worn or damaged parts need replacing. Compatibility is stated for the Carson XS-Chassis references 500404252, 500404253, 500404254 and 500404255, including Stadium Fighter blue, Stadium Fighter orange, Offroad Fighter Cage turquoise and Offroad Fighter Cage red. The moulded parts are shaped for the front assembly area, where upright and holder components support axle positioning and the connection points used in the chassis layout. This makes the set a practical choice for maintenance work, repair jobs or keeping matching spare parts ready in the workshop. In a hobby setup, replacement parts like these help bring a used chassis back into running condition after heavy track use, jumps or contact on rough ground. The compact set also fits neatly into an existing spares collection for 1:10 RC vehicle upkeep, especially where the XS platform is already part of the fleet.

Axles & drive shafts

Drakuro Front Cardan Shafts, RC spare part

soon available again

The Drakuro Front Cardan Shafts set supplies 2 replacement shafts for the front drivetrain of the Drakuro 1:8 4WD chassis. As a dedicated RC spare part, it focuses on one specific area of the model and supports accurate maintenance when worn or damaged front driveline parts need to be exchanged. The set is named for the front cardan shaft position, making its role within the chassis layout clear. It is intended for the Drakuro platform and links directly to the 1:8 4WD chassis listed in the data, which helps keep parts selection aligned with the correct vehicle family. Because 2 shafts are included, the pack matches the paired layout used at the front end. This makes the set useful for planned servicing as well as targeted repair work after heavy running. In the workshop, the shafts fit naturally into rebuilds, drivetrain refreshes, and spare-parts storage for the Drakuro range. For RC model enthusiasts maintaining a 1:8 4WD setup, a model-specific replacement part like this keeps attention on the exact component group rather than a generic universal fit.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Drakuro Steering Knuckle Set, chassis spare part

soon available again

The steering knuckle set is made for the Drakuro 1:8 4WD chassis and covers both the front and rear positions named in the data. That gives model-building enthusiasts a dedicated spare part for targeted maintenance on a platform built for RC running rather than a generic workshop substitute. The set is linked directly to the vehicle references 500409096 Drakuro BL 3S anthrazit/rot and 500409097 Drakuro BL 3S blau, which helps when matching replacement parts to the correct chassis family. In practical workshop use, steering knuckles sit at a critical point in the wheel assembly, where suspension movement and steering input meet. Replacing worn or damaged parts in this area can be an important step during a rebuild after repeated high-load sessions. Because the set is specified for front and rear use, it supports a more complete refresh of the running gear than a single-position replacement. This kind of spare part fits naturally into routine RC maintenance, whether the chassis is being repaired after contact, stripped for inspection, or prepared as a rolling base for the next outing. In a hobby workspace, a model-specific set like this helps keep service work focused on fit and function within the Drakuro platform.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

Virus-Ex Doge Bone rear, spare part, 2-piece

soon available again

The Virus-Ex Doge Bone rear set adds a focused drivetrain spare part for RC workshop stock, with 2 matching rear components shaped for the mechanical link between moving drive elements. The black metal finish and the rounded end sections shown in the image give these parts the technical form associated with model maintenance and replacement work. Each piece features a straight cylindrical shaft and ball-shaped ends, creating the kind of connection part used where rotating force needs to pass through the rear section of a model. As a dedicated rear version, this set is intended for the corresponding position on the Virus-Ex rather than as a general mixed-parts accessory. The 2-piece format provides a matched pair for repair tasks where both sides of the rear drivetrain need the same component. Within a model supplies range, that clear designation helps keep workshop organisation straightforward when selecting the correct spare part. The set fits naturally into routine servicing, rebuilds after wear, or the replacement of missing rear linkage parts in a Virus-Ex setup. For hobby benches stocked for upkeep rather than display, a clearly named rear doge bone pair keeps the next repair step close at hand.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

X10EB Rear Dogbone + Drive Cup RC Spare Parts

soon available again

The X10EB Rear Dogbone + Drive Cup set supplies the core rear drivetrain links for the X10EB in one matched replacement pack. With 2 rear dogbones and 2 drive cups, the set covers both sides of the rear drive layout and restores the mechanical connection that carries power from the transmission to the rear wheels. The dogbones use the familiar shaft format with ball ends and cross pins, a layout that lets the connection keep working as the suspension moves through its travel. The drive cups provide the receiving interface for that movement, with a slotted cup shape that accepts the dogbone ends during operation. This makes the set relevant when worn drivetrain parts lead to play in the connection, inconsistent drive delivery or a rougher running feel at the rear end. The metal parts shown in the set suit hobby users who maintain and rebuild their RC buggy with model-specific replacement components. As a workshop spare for the X10EB, this set fits routine servicing, repair after drivetrain wear, or keeping key transmission parts ready between running sessions. The 14 years marking is stated in the product data. For model builders and RC enthusiasts, these rear drivetrain parts support a focused, mechanical repair on the vehicle's driven rear assembly.  Warning! Not suitable for children under 14 years.

Axles & drive shafts

1:10 Center Main Shaft

only available from customer service

Carson 500405800 - Center Main Shaft for 1:10 scale models is aimed at model building enthusiasts who need a precisely fitting replacement shaft for their vehicle. The component is specially designed for the 1:10 scale and can be used in corresponding Carson models, ideal for targeted repair and maintenance of the driving function.   Warning! Not suitable for children under 14 years.

Axles & drive shafts

1:10 Differential complete

only available from customer service

500405775 - the complete 1/10th scale differential from Carson offers model building enthusiasts a suitable spare part for precise repair and reconditioning of their vehicles. As a complete unit, it simplifies replacement and assembly, ensures correct function in 1:10 scale and is an indispensable part of any workshop.

Axles & drive shafts

1:10 Drive Shaft front

only available from customer service

The Carson 1:10 front drive shaft (500405777) is a high-quality spare part for 1:10 scale models and is aimed at demanding model builders who expect stability and precise power transmission. Precisely manufactured for accurate replacement, it facilitates repair or performance optimization and ensures reliable operation in everyday use.

Axles & drive shafts

1:10 Drive Shaft real

only available from customer service

The Carson drive shaft 500405778 on a scale of 1:10 (Drive Shaft real) is a precise spare part for demanding model builders. Specially developed for 1:10 vehicles, it ensures reliable power transmission and is ideal for replacing or repairing defective drive parts. Accurate fit and performance bring your model back to top form.

Axles & drive shafts

1:10 Pivot

only available from customer service

Carson 1:10 Pivot (500405792) is an original spare part for 1:10 scale models and is aimed at ambitious model builders who are looking for replacements or specific upgrades. As a suitable accessory from Carson, it provides the necessary functionality in the body and offers a reliable basis for repairs or modifications.   Warning! Not suitable for children under 14 years.

Axles & drive shafts

1:10 Pivot Cover

only available from customer service

Carson 1:10 Pivot Cover - 500405790 is a cover part for 1:10 scale models from Carson. Model builders will find a suitable replacement or tuning part here that neatly closes off the area and rounds off the overall appearance of the vehicle. Ideal for enthusiasts who value detail. It complements the Carson parts range and is a targeted choice if you are looking for replacements or detail care for your 1:10 model.

Axles & drive shafts

1:10 Pivot Holder

only available from customer service

Carson 500405791 1:10 Pivot Holder is a precise spare part for 1:10 scale models and is aimed at model building enthusiasts who are looking for a true-to-original repair or targeted upgrading of their chassis. As a precisely fitting component, it supports the restoration of central steering and suspension functions.

Axles & drive shafts

1:10 Shaft Cover

only available from customer service

The Carson 1:10 Shaft Cover (500405789) is a precisely fitting addition for 1:10 scale models and offers the visual and functional completion of drive shafts. Model building enthusiasts appreciate the precisely manufactured solution for clean integration into existing chassis-ideal for detail-oriented repair and optimization.

Axles & drive shafts

BAD BUSTER drive shaft/wheel axle. (2) rear

only available from customer service

Axles & drive shafts

BAD BUSTER front drive shafts (2)

only available from customer service

Axles & drive shafts

BAD BUSTER rod set

only available from customer service

Axles & drive shafts

CDV Front Set 2x

only available from customer service

The Carson CVD Front Set 500405448 (2x) is a compact replacement set for the front drive side and is aimed at model builders who are looking for precise repairs or targeted upgrades. The two CVD components enable precise installation and provide a reliable supply for quick replacement in the event of maintenance or damage.   Warning! Not suitable for children under 14 years.

Axles & drive shafts

Centre drive shaft set CV-10

only available from customer service

Carson center drive shaft set CV-10 (500105133) is the original replacement and tuning part for CV-10 models. The center drive shaft set is specifically designed to repair or modify the drive axle of your model and ensures compatibility within the CV-10 series. A must for dedicated model builders and mechanics.

Axles & drive shafts

Crankshaft adapter set CV-10

only available from customer service

Carson 500105146, Crankshaft adapter set CV-10, is a crankshaft adapter set for the specific adaptation or replacement of crankshafts in model making. For model builders and hobbyists, this compact set offers a clear replacement and supplementary solution with which repair and conversion projects on the drive mechanism can be realized.   Warning! Not suitable for children under 14 years.

Axles & drive shafts

CROWN AND BEVELGEAR-SET CV-10

only available from customer service

Carson CROWN AND BEVELGEAR-SET 500105294 is a gear set with crown and bevel gears for model building applications. It is used to replace or supplement gear components and is aimed at model building enthusiasts who want to replace or adapt specific components. As an accessory from Carson, it complements existing assemblies and facilitates targeted replacement.

Axles & drive shafts

CV-10 Driver for central shaft

only available from customer service

Axles & drive shafts

CV-10B/T shaft 2 pcs

only available from customer service

Carson CV-10B/T drive shafts set of 2 (500405135) in black: Two shafts for model builders and hobbyists, compactly packaged as a set of 2. These black CV-10B/T shafts will complement your parts kit and will appeal to collectors and users looking for matching replacement components in a brand-typical design. Now available.   Warning! Not suitable for children under 14 years.

Axles & drive shafts

CY5 center differential 46Z

only available from customer service