Additional spares
Didn’t find what you were looking for? In this category, you’ll find more RC spare parts from Carson – precise fit, reliable, and ideal for repairs or custom tweaks to your model.
Additional spares
Didn’t find what you were looking for? In this category, you’ll find more RC spare parts from Carson – precise fit, reliable, and ideal for repairs or custom tweaks to your model.
More
Additional spares
1:10 Bokusa BL 2S, RC car accessory set
500405994€10.49
The Bokusa BL 2S uses a 1:10 XL chassis format, and this accessory set gathers 3 named components for that platform: a battery holder, covers and a wheelie bar. For model-building enthusiasts, that makes it a focused parts set for repair work, rebuilds or keeping a running chassis complete with the pieces stated in the data. The battery holder addresses the power area of the chassis, while the covers serve the matching body or chassis sections named for this set. The wheelie bar adds a separate rear-end component that suits setups where hard launches can put extra demand on the back of the car. The data also links the set to the Bokusa BL 2S orange and Bokusa BL 2S yellow versions, giving a clear reference to the variants named for this range. With a minimum age marking of 14 years, the set sits in the hobby-focused RC field rather than entry-level toy use. On the bench, these parts support a straightforward way to replace worn or missing chassis pieces on a compatible model. In a rebuild, the combination of holder, covers and wheelie bar helps return the 1:10 platform to a more complete running condition without guessing at unrelated parts.
Additional spares
1:10 Bokusa Wheel Set, model wheels, XL chassis
500900207€23.49
This 1:10 wheel set is made for the Bokusa BL 2S on the 1:10 XL chassis and brings the large-format look of the model back into a complete 4-wheel setup. With a diameter of 125 mm, a width of 60 mm and a 12 mm wheel hub, the dimensions are clearly defined for workshop planning, replacement work and chassis-specific preparation. The 4-piece layout covers the full running set in one pack, which is useful when a matched wheel format is needed across the whole vehicle rather than on a single corner. The stated Bokusa BL 2S variants in orange and yellow place this set within that model line, while the XL chassis reference keeps the application precise. For hobby workbench use, the combination of 125 mm diameter and 60 mm width gives a clear basis for checking clearance, stance and fit before installation. The 12 mm hub size also matters when selecting the correct mounting hardware for the chassis configuration. In the workshop, this set suits routine replacement, rebuilds after heavy running sessions or preparation of a Bokusa BL 2S kept as a ready spare. The defined dimensions make it easier to match an existing setup on the 1:10 XL platform without guesswork.
Additional spares
1:10 XL Chassis, model chassis, Bokusa BL 2S
500406000€21.99
The 1:10 XL Chassis brings a large-format base layout into the Carson Modelsport range, centred on a plastic chassis tray and the Bokusa BL 2S designation. With its XL format and clearly defined platform structure, this chassis suits hobby builds that start from the core frame and grow through individually chosen running components. The plastic chassis tray forms the main structural element and gives the build a dedicated base for further setup. Two colour versions are listed for the Bokusa BL 2S concept, orange and yellow, each carrying the same chassis identity with a different visual finish. The age marking is 14 years, which places this chassis in a hobby-oriented context rather than an entry-level toy range. Because the available data identifies this as a chassis rather than a complete ready-to-run vehicle, the focus stays on the base platform itself and on the scope it offers for a more individual build. On the bench, the 1:10 format gives model-building enthusiasts a familiar scale for planning a project around the chassis structure. In a collection or workshop setting, the XL layout and Bokusa BL 2S naming create a clear starting point for a custom RC model with a strong visual presence.
Additional spares
1:10 XS Chassis with Shaft Cover, spare part
500405930€20.99
Built around the 1:10 XS platform, this chassis with shaft cover serves as a dedicated spare part for selected CARSON models and restores the vehicle's core lower structure with the matching driveline cover in place. The black molded section combines the main tub and the cover layout in a form that matches the XS-Chassis design used across several off-road variants. Inside the chassis, the ribbed reinforcement pattern adds structural definition across the floor, while multiple screw posts and mounting holes provide the fixed points needed for compatible components from the original layout. Partition walls and integrated supports divide the interior into clear mounting zones, which helps keep the installation of matching assemblies consistent with the intended platform geometry. At both ends, the raised mounting sections and cylindrical connection areas are formed to accept the corresponding compatible assemblies used on the listed XS-Chassis vehicles. Compatibility is stated for CARSON XS-Chassis references 500404252, 500404253, 500404254 and 500404255, covering Stadium Fighter blue, Stadium Fighter orange, Offroad Fighter Cage turquoise and Offroad Fighter Cage red. The 14 years marking is stated in the product data. As a replacement component for an existing RC model, this part suits repair work, rebuilds and the return of a worn chassis base to its original platform layout.
Additional spares
1:10 XS Wheel Hex Nut Pin Kit, chassis spare
500405928€5.99
Built for the Carson XS-Chassis platform, this 1:10 wheel hardware set brings the key mounting parts for a complete wheel connection into one pack. The set contains 4 wheel hexes in 12 mm format, 4 M4 nuts and 4 pins, giving model-building enthusiasts the exact component group used between axle and wheel on the listed chassis versions. The wheel hexes sit at the centre of the mounting system, where the pin fixes the hex on the axle and the nut secures the wheel once fitted. That makes the set useful when original hardware is worn, misplaced during maintenance, or being replaced as a matched group across the vehicle. The 12 mm hex size is a common RC wheel interface, while the M4 nuts match the fastening point named in the data. Compatibility is stated for Carson XS-Chassis references 500404252, 500404253, 500404254 and 500404255. In workshop use, this set supports straightforward servicing on the Stadium Fighter blue, Stadium Fighter orange, Offroad Fighter Cage turquoise and Offroad Fighter Cage red variants named for the platform. It suits bench stock for rebuilds, wheel changes and routine running repairs on the compatible XS-Chassis models.
Pinions & gears
1:8 BL 13T Steel Pinion Gear, model accessory
500906202€10.79
In 1:8 model racing, small drivetrain parts shape how power reaches the wheels. This BL 13T Steel Pinion Gear hard is a compact transmission component for brushless 1:8 setups, built to sit on the motor shaft and pass rotation into the geartrain through its 13-tooth profile. The gear combines a central bore with a side fastening point, a layout that supports fixed mounting in the drive assembly. That construction matters during servicing, because a pinion must sit in the correct position to engage the matching gear evenly. The steel specification given in the data places the focus on the working surface that handles direct tooth contact. As a dedicated replacement or workshop spare, this part belongs in rebuilds, routine maintenance and gearing updates where worn drivetrain hardware needs to be exchanged with the correct tooth count. On the bench, the pinion fits naturally into motor and transmission work on 1:8 brushless models. In running setups, it serves as the small but essential link between motor output and the rest of the drivetrain, making it a useful component to keep ready for repairs and setup changes. Warning! Not suitable for children under 14 years.
Pinions & gears
1:8 BL 14T Steel Pinion Gear, RC accessory
500906203€10.79
In 1:8 brushless model driving, small transmission parts have a direct effect on how power reaches the wheels. This 14T steel pinion gear is made as a compact RC accessory for compatible 1:8 BL setups, where the tooth count becomes part of the gearing choice. The steel construction places the focus on a core drivetrain component rather than a cosmetic add-on. As a pinion gear, it sits at the motor side of the transmission and works with a matching spur gear to pass rotation into the rest of the drive system. The 14-tooth layout is a concrete specification for repair work, replacement of a worn gear, or a deliberate gearing change within an existing setup. The product image also shows a central threaded opening and a perpendicular threaded side hole, indicating a fastening arrangement designed for mounting on a shaft with a set screw. This kind of workshop part suits bench maintenance, rebuilds after heavy running, and targeted tuning of compatible RC vehicles. The age marking is 14 years+, matching its role as a technical hobby component within model-building and RC maintenance. Warning! Not suitable for children under 14 years.
Pinions & gears
1:8 BL 15T Steel Pinion Gear, RC spare part
500906204€10.79
In 1:8 brushless RC setups, the pinion is the small part that sets the first link in the drivetrain. This BL 15T Steel Pinion Gear uses 15 teeth and a steel body to mesh with the main drive gear in compatible model vehicles, giving hobby work a concrete, mechanical focus right at the motor shaft. The gear form shown in the data is built as a compact cylindrical pinion with straight outer teeth, a central bore and a side threaded hole for fastening. That layout allows the pinion to sit on the shaft and be fixed in place with a grub screw, an important detail when the motor's rotation has to transfer cleanly into the transmission. The 15T specification also matters in workshop planning, since tooth count is one of the key figures used when replacing a worn pinion or matching a drivetrain setup to an existing spur gear. As a steel spare part, it fits naturally into maintenance, repair and tuning work on 1:8 brushless RC models. On the bench, this kind of component is used during drivetrain service, rebuilds or gearing swaps where a fresh pinion restores proper meshing between motor and transmission. Age marking: 14 Years. Warning! Not suitable for children under 14 years.
Pinions & gears
1:8 BL 16T Steel Pinion Gear, model accessory
500906205€10.79
A small drivetrain part can make a clear difference in how a 1:8 brushless model puts power down. This BL 16T steel pinion gear is built as a dedicated model accessory for RC vehicle transmissions, with 16 teeth forming the drive interface between motor and spur gear. The gear uses steel for the toothed section, giving this heavily loaded contact point a material suited to repeated meshing in fast-running setups. Its compact cylindrical form keeps the part focused on the job of power transfer rather than adding bulk to the motor mount area. The central bore fits over the motor shaft, while the side fixing point is designed for a fastening screw that locks the pinion in place. That combination supports accurate positioning on the shaft and a direct mechanical link from the motor into the rest of the drivetrain. The 1:8 scale reference places it in the class of larger RC models where gearing choice plays a practical role in setup and maintenance. Whether used as a replacement for a worn gear or as part of a drivetrain change, this 16T pinion belongs in the workshop stock for compatible brushless RC vehicles. It suits rebuilds, routine servicing and gearing adjustments where a specific tooth count is needed to match the transmission layout. Warning! Not suitable for children under 14 years.
Additional spares
1:8 Drakuro Chassis, RC chassis, 4WD
500406050€41.99
The 1:8 Drakuro chassis brings a 4WD layout into a dedicated RC platform built around the fundamentals that matter to model enthusiasts. As a chassis-only format, it centres the project on the rolling base itself, creating a clear starting point for a build shaped by component choice, body selection and individual setup decisions. Within the Models & Accessories range, this Drakuro version stands as a focused foundation rather than a finished vehicle, which gives the chassis a different appeal from ready-to-run formats. The 4-wheel-drive arrangement distributes drive across all 4 wheels, supporting a composed feel when the model is set up for varied running conditions. The chassis designation also signals room for a more personal configuration, where electronics, bodywork and finishing direction can be chosen to match the intended use. Assembly time is stated in minutes in the product data, underlining its place in the hands-on side of the hobby. A battery is required separately. On the bench, the Drakuro chassis suits projects that begin with the platform and grow through careful parts selection. Once equipped, the 1:8 format and 4WD concept make it a strong base for builders who enjoy shaping how an RC model looks, responds and runs through their own setup choices. Warning! Not suitable for children under 14 years.
Additional spares
Akuma Chassis Stiffener, model spare part
500405987€6.49
Akuma and Virus model vehicles rely on accurately shaped chassis parts to keep a rebuild on track, and this 2-piece chassis stiffener set is made for the front and rear reinforcement positions named in the product data. The dark gray parts shown for this set use a long, narrow form with circular mounting holes at both ends and molded ribbing along the surface, giving the reinforcement area the correct component shape for replacement work. As spare parts for the chassis structure, these stiffeners are aimed at maintenance, repair and planned parts stocking rather than visual upgrades. The paired layout suits the stated front and rear use, while the molded channels and reinforcement ribs reflect the technical role of the parts within the chassis assembly. For model-building enthusiasts, that means a focused replacement set that addresses a specific structural section on compatible Akuma and Virus vehicles. In a workshop setting, the set fits naturally into rebuilds after wear, damage or routine inspection of the chassis area. The 14 Years marking is stated in the product data. For bench repairs or parts storage between running sessions, the 2 included stiffeners provide the named front and rear chassis reinforcement components. Warning! Not suitable for children under 14 years.
Additional spares
Akuma Steering Rack, model accessory, aluminum
500405990€8.49
The Akuma steering rack brings a key front-end control component into the workshop as an aluminum replacement part for Carson Akuma models. Its role sits directly in the steering assembly, where the rack forms the connection point for the linkage and supports the intended movement of the front wheels through the chassis layout. The part is described as an Alu steering rack and is intended as a model accessory within the Models & Accessories range. As a dedicated spare part rather than a universal fitting, it matches the Akuma designation named in the data and gives repair and maintenance work a clearly defined replacement for the steering area. The aluminum construction adds a specific material choice to this component, making it a relevant search term for hobbyists who maintain, rebuild, or refresh running gear parts. With the steering plate named in the source data, the part also speaks to focused servicing of the control hardware rather than a general upgrade bundle. In practical use, this kind of replacement belongs on the bench during routine maintenance, after wear in the steering mechanism, or when a build needs the correct Akuma-specific part to return the front end to working order. The 14 Years age marking is stated in the product data. Warning! Not suitable for children under 14 years.
Screws
Drakuro Ball Studs, model spare part set
500406066€6.49
The Drakuro Ball Studs set is a dedicated spare part for the 1:8 4WD Drakuro chassis and targets one of the small but essential connection points in the running gear. Ball studs sit at moving linkages where clean articulation matters, so replacing worn hardware can help bring back accurate mechanical response in the chassis layout. The set is listed for the Drakuro BL 3S platform and matches the anthracite/red 500409096 and blue 500409097 versions named in the data. With 4 ball studs plus 2 additional pieces, the pack provides a defined quantity for repair work rather than a generic mixed hardware selection. That makes it useful for planned maintenance, for replacing damaged linkage points after demanding runs, or for keeping the correct small parts on hand in the workshop. As a model spare part, the focus stays on fit within the named platform instead of broad compatibility claims. In practical use, this set suits bench repairs when steering or suspension connections need fresh hardware on the Drakuro chassis. It also fits neatly into a spares collection for 1:8 4WD running sessions, where the right replacement part can keep maintenance work focused and efficient. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Battery Holder, RC spare part
500406041€8.49
The Drakuro battery holder and centre differential cover are replacement parts for the 1:8 4WD chassis and address 2 core areas of the vehicle layout: battery retention and protection around the centre differential. The set is intended for maintenance work where original chassis parts are worn, damaged, or missing. The battery holder supports the correct placement of the battery within the chassis, while the centre differential cover restores the matching cover section in the drivetrain area. This makes the set useful for repairs after intensive running sessions as well as for planned workshop servicing. The designation in the data links these parts to Drakuro BL 3S variants, including Anthracite/Red and Blue versions, which helps place the spare within the Drakuro range without implying additional contents. In the workshop, these parts fit naturally into routine chassis maintenance, rebuild projects, and the replacement of used hardware on a 1:8 4WD platform. For model-building enthusiasts, a correctly matched spare part keeps the vehicle configuration consistent and supports continued running with the intended chassis structure. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Chassis Center Brace, chassis part
500406061€8.49
The Drakuro Chassis Center Brace is an aluminum center strut created for chassis stiffening on compatible 1:8 4WD Drakuro models. Its red anodized finish gives the part a crisp workshop look while the brace itself focuses on the middle section of the vehicle, where extra rigidity can support a more defined chassis response during running and tuning. Designed as a dedicated chassis part rather than a general accessory, this brace addresses one specific structural point in the layout. The aluminum construction suits the mechanical role of a center strut, and the anodized red surface makes the upgrade easy to identify during maintenance or rebuild work. Compatibility in the provided data points to the Drakuro BL 3S anthracite/red 500409096 and the Drakuro BL 3S blue 500409097, giving model-building enthusiasts a clear match within the range. Because the part is intended for 1:8 4WD chassis use, it sits naturally within larger off-road RC setups where the center section plays a key role in overall chassis balance. On the bench, the brace suits focused upgrade work on an existing Drakuro platform. At the track or on rough running surfaces, a stiffened center section can help keep the chassis layout more consistent under load, making this part a purposeful addition for hobbyists refining a compatible 1:8 4WD model. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro LED Strip for 1:8 Chassis, Light Set
500406070€8.49
The Drakuro LED strip set adds red and white lighting to the 1:8 4WD chassis named in the data, giving the model a clearer visual signature once fitted. With 2 separate LED strips, the layout can be integrated into the vehicle as a dedicated light upgrade rather than a general decoration. The colour split of red and white supports a front-and-rear lighting arrangement that suits RC vehicle styling and helps define the chassis lines more clearly. The set is identified for the Drakuro platform, including the versions 500409096 Drakuro BL 3S anthracite/red and 500409097 Drakuro BL 3S blue listed in the data. As an accessory in the models supplies category, it expands the visual setup of the vehicle while leaving the core drivetrain and running configuration unchanged. Mounted on a compatible Drakuro chassis, the strips add a stronger light presence for evening sessions, indoor running, or a more finished bench display between drives. The 2-piece format also supports a tidy installation concept across separate areas of the model, depending on the chosen layout. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Lower Arm Hinge Pins, RC Spare Part
500406056€5.49
The Drakuro Lower outer arm hinge pins set supplies 2 replacement pins for the lower control arm on the Drakuro 1:8 4WD chassis. With a stated length of 45 mm, this spare part is aimed at maintenance work where the correct pin dimension matters for the suspension assembly and for keeping the chassis hardware matched to the original specification. In the parts reference, the hinge pins are listed as lower control arm retaining pins, which identifies their role within the outer arm mounting area rather than as general-purpose hardware. That makes the set useful when wear, loss, or damage calls for a like-for-like replacement on the Drakuro platform. The 2-piece quantity also matches a focused repair task without adding unrelated hardware. The product data links this part to the Drakuro BL 3S variants in anthracite/red and blue, giving model-building enthusiasts a clear reference point within the range. On the workbench, a dedicated chassis spare part like this helps keep servicing organised by function and by model family. For rebuilds, routine checks, or replacing worn suspension hardware after running sessions, the exact 45 mm format gives a concrete specification to work from. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Lower Inner Arm Hinge Pins, RC spare part
500406052€6.49
These lower inner arm hinge pins are a dedicated spare for the Drakuro platform and address a precise chassis connection point rather than a general hardware need. With a specified length of 70 mm and a pack of 2 pieces, the set is intended for the lower control arm retaining position on the 1:8 4WD chassis used by the named Drakuro BL 3S models. In regular RC maintenance, suspension hardware needs the right dimensions and the right fit at the right mounting point. This set keeps that replacement specific: lower inner arm hinge pins for the chassis area named in the data, sized at 70 mm, and supplied as 2 matching pieces for the same suspension location. The reference to Drakuro BL 3S anthracite/red and Drakuro BL 3S blue ties the spare to the stated vehicle variants, which helps when checking compatibility within the range. Whether the chassis is being serviced after repeated track sessions or refreshed as part of a parts stock for the workshop, these pins support a straightforward replacement at the lower inner arm position. The focused specification makes them a useful choice when the goal is to keep a Drakuro 1:8 4WD chassis running with the correct suspension hardware. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Motor Mount Set, RC spare part
500406069€10.49
The Drakuro Motor mount set is a dedicated spare part set for the Drakuro BL 3S range and focuses on the motor mounting area of the chassis. The data names a plastic motor mount together with an aluminum mounting plate, giving model-building enthusiasts 2 specific replacement components for service work on the stated platform. The set is linked in the data to the 1:8 4WD chassis and to the Drakuro BL 3S versions in anthracite/red and blue. That makes it a targeted choice when the motor mounting section needs the exact parts named for repair, maintenance, or a like-for-like replacement. The material combination is clearly defined: the motor mount is plastic, while the mounting plate is aluminum. This keeps the scope of the set clear and avoids guesswork around unspecified extras or broader conversion parts. In workshop use, the set suits rebuilds after wear in the motor area, replacement during routine servicing, or keeping matching spare components ready for the Drakuro chassis. For hobby benches centered on 1:8 4WD running gear, a model-specific mount set helps keep repairs focused on the exact section named in the product data. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Rear Axles, spare part, 2-piece set
500406055€10.49
The Drakuro Rear axles set supplies 2 rear wheel axles for the 1:8 4WD chassis named in the data, giving the rear running gear the exact replacement part type rather than a generic hardware substitute. With the Drakuro designation tied directly to the chassis reference, the set fits naturally into maintenance work focused on the rear axle area. Because the data identifies these parts specifically as rear wheel axles, the set is clearly aimed at the wheel-carrying section at the back of the chassis. The 2-piece quantity corresponds to one rear pair, which helps keep servicing straightforward when a rebuild calls for both sides. In workshop use, a dedicated axle set like this supports cleaner parts planning than mixing unmatched components from general assortments. The 1:8 scale reference and 4WD chassis note also place the set within a defined model platform, which matters when selecting drivetrain and suspension-related replacements. On the hobby bench, this kind of spare part belongs in regular upkeep, damage repair or a more complete chassis refresh. It suits rebuild sessions where the rear end is being stripped, checked and reassembled around the specified axle position. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Servo Horn, RC spare part for 1:8 chassis
500406046€4.49
The Drakuro Servo horn is a dedicated replacement part for the 1:8 4WD chassis in the Drakuro range. As the link between the steering servo and the chassis steering mechanism, this small component plays a direct role in transferring servo movement into wheel input, making it a relevant part for repair and routine maintenance. The available data identifies the servo horn specifically with the Drakuro platform and places it in the RC models and accessories segment. That clear platform reference matters on the hobby bench, where matching a spare part to the correct chassis helps avoid unnecessary trial and error during servicing. The part is listed as a servo lever, which points to its mechanical role in the steering linkage rather than to electronics or body hardware. This replacement suits workshop stock for keeping a Drakuro 1:8 4WD chassis ready for continued use after wear, damage, or a missing original part. In a maintenance session, the servo horn belongs among the key linkage components checked when steering response needs to be restored with the correct platform-specific spare. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Servo Saver Set, steering chassis part
500406040€16.99
The Drakuro Servo saver/steering arm set is a dedicated spare part set for the 1:8 4WD chassis used in the Drakuro BL 3S range. Named components include the servo saver and steering lever set, giving model-building enthusiasts the exact steering-area parts identified for this platform rather than a generic fit solution. Compatibility is stated for the Carson references 500409096 Drakuro BL 3S Anthracite/Red and 500409097 Drakuro BL 3S Blue. That makes the set relevant when the steering linkage on one of these versions needs replacement with the specified parts. Within the front steering layout, the servo saver works with the steering arm section as part of the control path between the steering servo and the wheels, so replacing worn or damaged parts in this area helps return the chassis to its intended mechanical setup. The set is focused on these named steering components, which keeps part selection straightforward for workshop use. On the bench, this kind of chassis-specific spare part suits routine maintenance, repair after running damage, or keeping a compatible Drakuro model ready for the next session. For hobby shelves with active RC vehicles, a clearly assigned steering replacement set saves time when the correct parts are needed. Warning! Not suitable for children under 14 years.
Axles & drive shafts
Drakuro Steering Link Set, model accessory
500406044€6.49
A steering system only feels right when the linkage matches the chassis it was made for. This Drakuro Steering link set is specified for the 1:8 4WD chassis and gives model-building enthusiasts a dedicated replacement option for the steering setup on compatible Drakuro vehicles. The set is listed as a model accessory in the Models & Accessories range and is assigned to the Drakuro BL 3S platform. Compatibility is stated for 500409096 Drakuro BL 3S Anthracite/Red and 500409097 Drakuro BL 3S Blue, which makes the intended fit easy to identify when planning maintenance or keeping workshop spares ready. As a steering link set, it belongs to the front-end control hardware that connects steering movement through the chassis layout, making it a relevant part for repair work after wear or damage. The focus here is not on a generic spare, but on a named set for a defined vehicle platform. In workshop use, this kind of chassis-specific linkage helps keep servicing organised and avoids guesswork when replacing worn steering parts on a compatible 1:8 4WD model. It suits routine upkeep, targeted repairs, and parts storage alongside other Drakuro running gear components. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Upper Arm Hinge Pins, RC spare part
500406054€6.49
The Drakuro Upper Arm Hinge Pins set supplies a focused replacement for the upper control arm retaining position on the Drakuro 1:8 4WD chassis. With 2 pins at 40 mm length, the set addresses a specific suspension mounting point rather than a general hardware assortment, which keeps repair planning clear at the bench. In the chassis layout, hinge pins form the connection point that holds the arm in its intended position while allowing the suspension assembly to articulate as designed. Replacing a worn, bent, or missing pin in this area helps return the upper inner arm mounting to its stated configuration. The part reference in the data links this set to the Drakuro BL 3S variants listed for the 1:8 4WD platform, including anthracite/red and blue versions. This kind of spare part suits routine maintenance, targeted repairs after running sessions, or keeping key suspension hardware on hand between rebuilds. In a workshop setup, the 2-piece pack gives the exact quantity stated for this replacement task without shifting attention to unrelated fittings or general-purpose fasteners. Warning! Not suitable for children under 14 years.
Additional spares
Drakuro Wheel Hex-Hub, RC spare part, 1:8
500406049€6.49
Built for the Drakuro platform, this wheel hex-hub set supplies the small but essential mounting parts that sit at the wheel connection points of the 1:8 4WD chassis. The pack contains 4 wheel hex-hubs and 4 spacer pieces, giving the specified vehicle layout the matching parts needed for replacement work. The set is assigned to the Carson Drakuro BL 3S versions 500409096 in anthracite red and 500409097 in blue, which keeps compatibility tied to clearly named models rather than broad guesswork. In RC maintenance, these parts belong to the hardware that supports the wheel mounting interface, making them relevant when worn or missing components need to be exchanged on the stated chassis. The combination of hex-hub and spacer piece keeps the replacement focused on the exact area named in the data instead of a generic mixed hardware pack. On the bench, the 4-piece wheel hex-hub set suits planned servicing, targeted repairs and keeping matching replacement parts ready for the next rebuild session. For hobby workshop use on the Drakuro 1:8 4WD chassis, the clearly assigned fit helps keep parts selection straightforward. Warning! Not suitable for children under 14 years.
Additional spares
Front Bumper for Virus and Akuma RC Models
500205942€4.39
A front bumper takes the first contact at the nose of an RC vehicle, and this replacement part is shaped for that exact role on compatible Carson models. The black component combines a rounded horizontal bar with a flat top mounting bracket, creating the front-end guard layout shown for the Virus and Akuma range. The part is specified as a front bumper for Virus 4.0, 4.1, 4.2, 4.3 and Race models, and it is also listed for Akuma. The mounting section uses 2 round screw holes, a concrete fixing layout that helps match the part to the correct front attachment points on the compatible chassis. As a dedicated spare part, it suits repair work after front-end wear or impact damage and supports a tidy rebuild with the intended shape rather than an improvised substitute. The cylindrical bumper form and textured finish keep the look close to the original style of the vehicle line. In workshop use, this bumper fits naturally into routine maintenance, collision repair or a full refresh of a well-used RC model. It also serves as a practical stock spare for hobby benches where Virus or Akuma vehicles are kept running across repeated driving sessions. Warning! Not suitable for children under 14 years.
Additional spares
KoD Gear Housing, RC spare part, front rear
500405883€12.79
The KoD Gear housing front/rear is a dedicated RC spare part for Carson Modelsport vehicles, supplied as a 2-piece housing set with a larger main section and a matching cover. The black moulded parts are shaped for the drivetrain area, where a compact enclosure helps organise mechanical components and supports clean integration into the chassis layout. The larger housing features a circular opening at the front, upright mounting ears with through-holes, cylindrical posts for fasteners, side mounting points and a rectangular lower cutout. The smaller cover adds matching screw locations, recessed surface detailing and reinforced rib sections that follow the form of the main casing. Together, these details indicate a housing designed to enclose and support connected transmission or gear components while leaving the required access points for mounting and assembly. For hobbyists maintaining a KoD model, this kind of replacement part helps restore the original fit of the front or rear mechanical housing area. It suits workshop use during repair, parts replacement or a full rebuild, especially when worn or damaged casing sections need to be exchanged for fresh components. The 2 matching pieces can be kept ready in the spares box for routine servicing or used to complete a drivetrain housing section during a more extensive chassis refresh.
Pinions & gears
Pinion Gear 10T, RC spare part, module 0.8
500013400€5.79
A small change in the drivetrain can alter how an RC model puts power down, and this steel pinion gear brings that adjustment into a compact 10T format. With module 0.8 teeth, it is built for compatible drive systems that require this exact gear size and tooth profile. The gear is designed as a technical spare part for model maintenance, repair, or setup changes. Its steel construction focuses on the working surface that matters most: the toothed outer ring that meshes with the matching gear in the transmission. A central threaded bore and a side hole are provided for mounting, and the included set screw fixes the gear onto the shaft. That fastening method supports quick replacement when a drivetrain is being serviced or reconfigured around a different ratio. In use, the key requirement is compatibility: module 0.8 and 10 teeth must match the existing drivetrain layout. This makes the gear a practical choice for workshop stock, routine wear replacement, or targeted tuning on RC vehicles that use this specification. Age 14+ Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 12T, RC spare part, module 0.8
500013437€5.89
A small pinion gear plays a central role in how an RC drivetrain delivers power, and this 12T version is built for that exact task. With module 0.8 teeth and a steel body, it is made for model setups that rely on clean gear engagement and a defined transmission ratio. The gear uses a threaded centre bore and comes with a separate black set screw, so the pinion can be fixed onto the shaft with a direct mechanical connection. That fastening method supports accurate placement during assembly or replacement work and helps keep the gear aligned in the drive system. As a dedicated spare part, it suits repairs where a worn pinion needs to be exchanged for the same tooth count, and it also fits tuning work that depends on specific drivetrain components rather than general-purpose hardware. The compact metal construction matches the technical character expected from RC workshop parts. On the bench, this kind of component matters when rebuilding a transmission, refreshing a used model or sorting parts for a fresh drivetrain setup. The 14 Years age marking places it clearly in the hobby category, where exact specifications such as 12T and module 0.8 are part of choosing the right gear for the job. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 12T, steel gear for model drive
500013420€5.49
A pinion gear is one of the small parts that has a direct effect on how a model drive feels in use, and this steel version combines module 0.6 gearing with 12 teeth for compatible RC and model drivetrain setups. The silver-coloured gear body is paired with a separate black grub screw, creating a compact replacement part for service, repair or drivetrain maintenance. The cylindrical gear form carries straight external teeth, a central bore and a side threaded hole for fastening. Once fitted to the motor shaft with the grub screw, the pinion works as the driving gear that meshes with the matching spur gear in the transmission. That interaction is what passes motor output into the rest of the drivetrain, so the tooth count and module matter when replacing a worn part or matching an existing setup. The steel construction makes it a focused choice for hobby work where fit and clean engagement are the priority. In workshop use, this part suits routine maintenance, drivetrain refreshes and rebuilds on compatible models. The 14 years marking is stated in the product data. For model-building enthusiasts, a small transmission part like this can be the detail that brings a drive system back into proper running order after wear or a gearing change. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 13T, model accessory, steel 0.8
500013403€5.99
A pinion gear is one of the small parts that shapes how power moves through a model drivetrain, and this version combines a steel build with module 0.8 gearing and 13 teeth for a clearly specified replacement or workshop component. The compact form, silver-coloured machined finish and separate grub screw point to a part made for precise mechanical installation in RC model assemblies. The gear uses straight teeth around the lower section and a central bore through the body, so it can sit on a motor shaft or similar drive point and mesh with the corresponding transmission gear. A threaded side hole takes the black grub screw, which locks the gear onto the shaft once the position is set. That fastening method supports accurate placement during servicing, ratio changes or worn-part replacement. For hobby benches that keep common drivetrain spares ready, a 13T pinion fills a specific gearing slot rather than acting as a generic substitute. In use, this kind of component suits rebuilds, maintenance sessions and drivetrain tuning where the existing module must be matched correctly. It also works as a straightforward spare for models already set up around module 0.8 gearing, keeping repair work focused on fit, tooth count and secure fastening. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 13T, model accessory, steel M0.6
500013421€5.59
A small change in gearing can alter how a model drive system comes together, and this pinion gear is built around that exact task. The steel gear uses module 0.6 teeth and a 13T layout, giving hobby setups a clearly defined replacement or tuning part for compatible drivetrains. The gear is shown with straight teeth, a central bore and a threaded side hole. That construction points to shaft mounting, with the included grub screw fastening the gear onto the matching shaft position inside a motor or transmission assembly. For maintenance work, worn drivetrain parts can be swapped without changing to a different module, and for setup changes the 13-tooth format provides a specific gearing option rather than a generic spare. The compact metal construction also suits parts storage alongside other workshop essentials for RC and model servicing. On the bench, this kind of component fits naturally into rebuilds, repairs and routine drivetrain checks where exact fit matters more than broad compatibility claims. The age marking in the data is 14 years, matching its role as a technical model accessory for hobby use. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 14T, RC spare part, module 0.8
500013439€6.39
Small drivetrain parts decide how cleanly power reaches the wheels, and this steel pinion gear brings that focus down to a clearly specified 14T format with module 0.8. The machined metal form, central mounting bore and separate grub screw create a compact RC spare part built for shaft mounting in geared model systems. The 14-tooth layout defines the gearing at the motor side and makes this component a targeted choice when maintaining or replacing a worn drive part. Its toothed lower section is designed to mesh with a matching gear, transmitting rotational force from the shaft into the next stage of the drivetrain. The hub section provides the mounting point, while the black screw secures the gear on the shaft as part of the assembly. The steel construction suits the mechanical role of a pinion in RC model transmissions where fit, tooth form and secure fastening all matter. In workshop use, this spare part supports routine servicing, drivetrain repairs and ratio-specific replacement jobs on RC models. It also fits neatly into a parts stock for hobby benches where commonly used transmission components need to be ready for the next rebuild or repair. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 14T, RC spare part, steel M0.6
500013422€5.99
A small change in gearing can noticeably alter how an RC model puts power to the ground, and this steel pinion gear brings that adjustment into a compact drivetrain part. With module 0.6 and 14 teeth, it is built for compatible gear trains where the motor shaft drives the spur gear through a defined tooth profile. The steel construction makes this a dedicated mechanical component for repair, maintenance or drivetrain setup work, while the side bore and included set screw provide the fixing point on the shaft. In use, the pinion sits directly at the motor output and transfers rotational force into the transmission, so the tooth count becomes a practical setup detail rather than just a number. A 14T pinion can be used when an existing gear needs replacement with the same specification or when a compatible model calls for this exact module and tooth count. On the workbench, it fits naturally into rebuilds, routine servicing and parts-box preparation for RC running gear. In a workshop setup for hobby projects, the separate screw and compact format keep the focus on one essential task: mounting the gear correctly and restoring a compatible drivetrain to working order. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 15T, RC accessory, steel module 0.8
500013405€6.79
A pinion gear is one of the small parts that directly shapes how power reaches the drivetrain, and this 15T version is built for that exact task in RC model setups. The steel gear uses module 0.8 teeth, giving model-building enthusiasts a clearly defined replacement part for transmission work, repairs, and rebuilds. The compact gear body combines a toothed lower section with a central mounting bore and a side threaded hole for fastening. A set screw is included and secures the gear on the shaft, so the part can be fitted where a worn or damaged pinion needs to be replaced. The machined tooth form is designed for meshing with a matching gear standard, which matters when maintaining smooth power transfer in hobby drivetrains. Instead of a general hardware part, this is a dedicated RC transmission component with a specific 15-tooth count and module 0.8 format. On the workbench, that makes it useful for routine maintenance, drivetrain refreshes, and keeping compatible models in running order. Age 14+ is stated in the product data. Whether the task is replacing a used gear or preparing parts for the next rebuild, this steel pinion belongs in the core stock of RC workshop spares. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 15T, RC spare part, steel module 0.6
500013423€6.09
A 15T pinion gear with module 0.6 adds a core drivetrain part to RC model work, pairing a steel body with a compact format made for precise mechanical engagement. The straight tooth profile, centred bore and threaded side hole show a layout built to mount on a shaft and transfer motor output into the transmission. The separate grub screw is included for fastening, so the gear can be fixed directly through the side thread instead of relying on a press fit alone. That construction supports controlled installation in compatible assemblies where the tooth count and module need to match the existing gear train. As a replacement part, the 15-tooth format can restore a worn drive connection; as a tuning part, it provides a defined gearing option for model builders working on drivetrain setup. The steel construction also makes it a clear choice where a metal pinion is specified in the build. On the workbench, this gear fits naturally into maintenance, rebuild and upgrade tasks around RC transmissions and motor mounts. It suits hobby projects that call for a compact pinion with module 0.6, a secure screw fixing and a clearly defined 15T configuration. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 16T, RC spare part, Module 0.6
500013424€6.19
A small drivetrain part can make a clear difference in how an RC model is set up, and this pinion gear brings that focus down to the essentials with a 16-tooth layout, module 0.6 sizing and steel construction. The separate black set screw is included for mounting the gear on a shaft, matching the compact, workshop-oriented character of a true replacement component. The toothed lower section and central bore show its mechanical role at a glance: this gear is made to sit in the drive system and transmit motor force into the rest of the transmission. For model-building enthusiasts, that makes it useful both in routine maintenance and in gearing changes where a specific tooth count is required. Steel gives the part a clear technical profile for repeated use in compatible RC assemblies, while the defined module 0.6 format helps match it to the intended drivetrain standard. On the bench, it fits naturally into repair sessions, rebuilds and tuning work on RC vehicles and other compatible model drive systems. The 14 Years age marking is stated in the product data, and the compact format keeps the focus on one exact task within the transmission: secure fitment and controlled gear engagement. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 16T, RC spare part, Module 0.8
500013406€6.89
A 16-tooth pinion gear in module 0.8 brings a key drivetrain detail into RC workshop maintenance. The steel construction suits use as a replacement transmission part where clean tooth engagement and a defined gear size matter in a compatible setup. The gear is designed for shaft mounting, with a central bore and a threaded side hole that takes the included set screw. This fastening method allows the pinion to be fixed on a compatible motor shaft so torque can be passed into the gearbox. The straight-tooth profile and compact hub shape make the part easy to identify when matching an existing drive layout or replacing a worn gear in a model already in service. Age 14+ is stated in the product data. In hobby use, this kind of spare part belongs on the bench alongside routine drivetrain servicing, rebuilds and ratio adjustments on RC models. It suits enthusiasts who keep compatible vehicles running with the correct mechanical parts and want a clearly specified 16T steel pinion for module 0.8 applications. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 17T, RC spare part, module 0.6
500013425€6.69
A 17T pinion gear with module 0.6 brings a concrete tuning and maintenance part to the drivetrain of compatible RC models. The steel gear is built for the job of transferring motor output into the transmission, while the compact form and straight-tooth layout suit precise engagement with the matching gear size and module. The central bore is paired with a side threaded hole, and the included grub screw fixes the gear onto the motor shaft for a defined mechanical connection. That makes this spare part useful both when replacing a worn gear and when changing the tooth count within a compatible setup. In workshop use, a pinion like this directly affects how the motor feeds power into the rest of the drivetrain, so the 17-tooth specification is a meaningful detail for setup planning. The steel material keeps the focus on a classic transmission component used in many hobby-grade drive systems. On the bench, the gear fits naturally into routine service work, rebuilds and drivetrain adjustments for RC vehicles and model applications that use module 0.6 gearing. Age marking: 14 years. The included grub screw completes the mounting hardware needed for installation on a compatible shaft. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 18T, model accessory, steel 0.6
500013426€6.79
A compact drivetrain part can change how a model puts power to the ground, and this steel pinion gear does exactly that with module 0.6 teeth and an 18T layout. The machined metal form and cylindrical hub create a focused, technical look that suits workshop benches, maintenance sessions and fresh gearing setups alike. As a model accessory, the gear is built for use in compatible drivetrain assemblies where tooth count and module need to match the rest of the transmission. The 18-tooth configuration offers a concrete gearing choice for tuning or replacement work. Steel construction gives this component the material specification stated in the data, while the separate grub screw forms part of the mounting system shown for the hub. The central bore and side fixing point indicate a shaft-mounted design that is secured mechanically rather than clipped into place. That makes the part relevant for repair jobs, routine servicing and planned drivetrain changes on hobby models. On the bench, the small format is easy to handle alongside other transmission parts during fitting and adjustment. In running setups, a correctly matched pinion like this becomes one of the key links between motor output and the rest of the gear train. Age marking: 14 years and up. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 18T, RC drivetrain gear, module 0.8
500013408€7.29
A pinion gear is one of the smallest parts in an RC drivetrain, yet it has a direct effect on how motor power reaches the transmission. This steel version uses module 0.8 gearing and 18 teeth, giving model-building enthusiasts a clearly defined spare or replacement part for compatible RC applications. The gear is made as a shaft-mounted drive component with straight teeth, a central bore and a side threaded hole. A separate set screw is included for fastening the gear onto the shaft, so the connection between motor and drivetrain can be secured during repair or setup work. The compact format makes it easy to keep on hand in a spares box for workshop use, whether the task is replacing a worn gear, restoring a transmission, or preparing a planned gearing change. The steel construction suits the mechanical role of a pinion in repeated drive engagement. In practice, this 18T gear fits naturally into bench work around RC vehicles and other compatible model drivetrains where module 0.8 is required. Age marking: 14 Years. As a focused transmission part, it supports maintenance sessions, rebuilds and parts-based tuning with a concrete, easy-to-identify specification. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 19T, RC accessory, Module 0.6
500013427€6.89
A pinion gear is one of the key parts that defines how power reaches the drivetrain, and this steel version brings a clear specification for RC maintenance and setup work. With module 0.6 and 19 teeth, it is intended for model applications that require that exact gear size and tooth profile. The gear is shown as a compact metal drive component with straight teeth, a central bore and a side threaded hole. That layout allows the gear to sit on a motor shaft and be secured with the supplied grub screw, so the drive can transfer rotation into the transmission with the intended mesh. For hobbyists working on repairs, replacements or gearing changes, the exact 19T count is the practical detail that determines compatibility with the matching spur gear and drivetrain layout. The steel construction makes it a focused choice for RC workshop stock where a specific module and tooth count are needed. On the bench, this kind of part is used during drivetrain servicing, when an existing pinion is replaced or a setup is changed to alter the gearing ratio of a model. It also suits spare-parts storage for RC vehicles that use module 0.6 gearing and a screw-fixed motor pinion. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 20T, RC spare part, Module 0.6
500013428€7.29
A compact pinion gear sits at the heart of many RC drivetrains, where tooth count and module determine how power reaches the wheels. This version uses a 20T layout with module 0.6 and a steel build, giving model-building enthusiasts a clearly defined spare part for maintenance, replacement work or gearing changes in compatible setups. The gear is supplied with a separate grub screw that fastens the hub to a shaft through the threaded side hole, a practical detail for secure installation in motor or transmission assemblies. The machined form includes a central bore and side teeth for transmitting rotation between connected drive components. As a models supplies part, it fits naturally into workshop stock for rebuilds, service intervals and targeted drivetrain tuning where the specification must match the existing system exactly. Age marking: 14 Years. On the bench, the 20T steel gear supports careful setup work when a worn or unsuitable pinion needs replacing. In a running model, the correct module and tooth count help maintain the intended gear mesh within a compatible drive assembly, whether the focus is repair, restoration or a fresh mechanical setup. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 21T, RC drivetrain accessory
500013429€7.29
A 21T pinion gear is a small part with a direct effect on how an RC drivetrain comes together. This version uses a module 0.6 tooth profile and steel construction, giving model-building enthusiasts a clearly defined replacement part for compatible drive systems. The gear is designed with a central bore for mounting on a shaft and a side threaded hole for the included grub screw. That fastening method matters in practice, because the screw fixes the gear on the shaft instead of relying on a push fit alone. The evenly cut teeth are made to mesh with a matching module 0.6 gear, which is the key detail when replacing a worn drivetrain part or preparing a fresh setup. In workshop use, the 21T count is also a concrete selection point when an existing transmission calls for the same specification. This accessory fits naturally into repair work, maintenance sessions and parts storage for RC models that use the matching format. On the bench, it supports a clean swap when a drive component needs replacement, and in a tuning collection it serves as a defined steel gear option for compatible assemblies. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 22T, RC spare part, steel module 0.6
500013430€7.79
A 22T pinion gear with module 0.6 brings a defined gearing specification to RC model drivetrain work. The steel construction and machined tooth profile make it a functional choice for maintenance, replacement, or setup changes where this exact gear size is required. The gear is built as a compact drive component with straight teeth around the circumference, a central bore, and a threaded side hole for fastening. A grub screw is included to lock the pinion onto the shaft, so the gear can transmit motor output into the rest of the drivetrain. In workshop use, details such as the 22-tooth count and module 0.6 matter because they determine how the gear meshes with the matching transmission components. The steel finish also suits repeated handling during servicing and rebuilds. This spare part fits naturally into bench sessions focused on repair, upkeep, or gearing adjustments in RC models. Age marking: 14 years. For hobbyists keeping a drivetrain running smoothly, a correctly specified pinion is one of the small parts that makes a setup work as intended. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear 24T, model accessory, steel
500013432€8.49
A steel pinion gear with module 0.6 and 24 teeth brings a clearly specified drivetrain part into model maintenance and repair work. The machined gear format and central bore are designed for mounting on a shaft, while the raised hub supports the fastening point for the included grub screw. In a drive assembly, the pinion transfers rotational force from the motor shaft into the gear train, making tooth count and module an important match for compatible setups. The 24T layout gives a concrete reference when replacing a worn gear or preparing a drivetrain with the same specification. The separate black fixing screw is included as part of the mounting hardware, so the gear can be locked in place once fitted. The steel construction names the material directly for hobbyists who search by drivetrain component and tooth format rather than by a general spare-part label. This component fits naturally into workshop routines such as servicing a model, replacing a damaged drive part or keeping a matching spare ready in the parts box. The age marking in the data is 14 years and up. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear M0,6 27T, spare part, steel
500011107€9.29
A pinion gear defines how motor power reaches the transmission, and this steel version with M0,6 pitch and 27 teeth is built for that exact drivetrain task in compatible RC models. The compact gear body, central bore and separate grub screw create a straightforward shaft-mounted layout that suits repair benches, replacement work and gearing adjustments. The 27T tooth count sets a specific ratio step, while the M0,6 pitch is the key matching dimension for correct engagement with the corresponding spur gear. Straight teeth run evenly around the outer edge, and the raised hub houses the threaded side fixing point for the grub screw. That fastening method locks the gear onto the motor shaft through the hub rather than relying on a press fit alone. The steel construction adds the material specification many hobbyists look for when selecting drivetrain hardware for regular service work. On the bench, this spare part fits naturally into gearbox maintenance, worn-gear replacement or a planned ratio change on a compatible setup. Age 14 Years. Checking pitch, tooth count and shaft fit before installation keeps the drivetrain matched to the existing transmission components. Warning! Not suitable for children under 14 years.
Pinions & gears
Pinion Gear M0,6 29T, RC spare part
500011109€9.29
A pinion gear is one of the small parts that has a direct effect on how an RC drivetrain transfers power, and this Carson Modelsport version is specified as a steel gear with module 0.6 and 29 teeth. The compact format, raised hub and separate grub screw point to a classic motor-shaft mounting setup used in many model drive systems. The 29T tooth count and M0.6 pitch define how the gear meshes with a matching transmission gear, so this spare part is suited to repair work as well as planned gearing changes on compatible models. Steel construction makes it a functional choice for a component that sits at the centre of repeated rotational contact. The centre bore fits onto the shaft, while the grub screw locks the gear in place through the hub. That combination gives hobbyists a concrete replacement part for restoring a worn drive assembly without replacing a larger gearbox section. On the workbench, this kind of component belongs in every well-stocked RC spares box, whether the task is routine maintenance, drivetrain servicing or preparing a compatible model for its next run. Age marking: 14 Years Warning! Not suitable for children under 14 years.
Additional spares
RC Box & Servo Mount Set for Virus and Akuma
500405591€22.49
The RC Box & Servo Mount Set is a model-specific replacement set for Carson Virus and Akuma platforms, built to restore the electronics enclosure and servo mounting area with matching black housing parts. Its 3-piece layout brings together a rectangular front frame, a deep main box and a separate cover, creating a defined structure for the installation zone inside the vehicle. The front section uses a large central cutout, raised inner rim and corner mounting tabs, while the main housing adds side mounting ears and a deeper shell for enclosed placement. The cover section completes the assembly with its own mounting tabs and fastening point, so the set follows the original multi-part construction rather than a simplified universal shape. This makes it useful for repairs after wear, for rebuilding a used chassis, or for keeping a compatible buggy ready for the next running session. The moulded parts are designed around screw fixing, with visible holes and support details that help the sections sit in their intended positions. Compatibility is stated for Virus 4.0, 4.1, 4.2, 4.3 and Race, as well as Akuma. In the workshop, this kind of replacement set supports tidy electronics placement and a proper base for the servo area when an original housing section needs to be exchanged. Age marking: 14 years and up.
Pinions & gears
Steel Pinion Gear 17T, spare part, M0.8
500013407€7.29
A 17T steel pinion gear with M0.8 pitch brings a clearly specified drivetrain component into RC model maintenance and tuning work. The machined gear format and separate set screw create a direct, mechanical connection at the motor shaft, where the teeth mesh with the matching transmission gear to pass power into the drivetrain. The threaded hub allows the set screw to lock the pinion in place on a compatible shaft, which is the key step for controlled power transfer in many model vehicle drive systems. Steel construction makes this part a focused choice for replacing a worn pinion or keeping a matching spare in the workshop. The 17-tooth count and M0.8 module are the decisive fit details for model builders comparing gearing components, because both values need to match the intended drivetrain layout. Age marking: 14 Years. In workshop use, this spare part fits naturally into repair benches, gearbox service and drivetrain refreshes for compatible RC models. It also suits hobby stock for planned gearing changes, where a specific tooth count and module are needed before the next running session. Warning! Not suitable for children under 14 years.
Pinions & gears
Steel Pinion Gear 19T, spare part, M0.8
500013409€7.59
A 19-tooth pinion gear is a small part with a direct effect on how power reaches the transmission, and this steel version in module M0.8 is built for that exact drivetrain task. The machined gear form, central bore and raised hub create a compact connection point between motor shaft and gear train in compatible RC model setups. The straight-tooth gear profile is designed for meshing with matching transmission components in M0.8 systems, while the separate set screw locks the pinion onto the shaft through the hub. That fastening method supports a defined fit during replacement work and routine drivetrain maintenance. As a spare part, the gear is suited to restoring a worn drive connection or changing the gearing specification on a compatible model. The steel finish and compact dimensions shown by the part itself keep the focus on mechanical function rather than decoration. In workshop use, the pinion can be fitted during a repair, a drivetrain refresh or a gearing adjustment on RC vehicles that use this tooth count and module. Age 14+ Warning! Not suitable for children under 14 years.
Additional spares
Virus 4.0 Alu-Hex Hub 17mm, wheel hub set
500205938€13.49
The Virus 4.0 Alu-Hex Hub 17mm brings a key drivetrain connection into a compact metal hardware set, pairing 17 mm wheel mounting with a threaded hub format for RC model maintenance and replacement work. The red anodized finish gives the adapters and nuts a clear visual match on the bench while the silver pins and black grub screws complete the fastening layout. Each adapter has a hollow centre and a cross-hole near the hex base, showing the intended pin-mounted connection on the axle or shaft. The metal pin slides through the shaft, the hub fits over that point, and the grub screw secures the assembly in place before the matching hex nut fastens the wheel. This sequence makes the mounting method easy to follow when servicing worn wheel fittings or preparing a fresh setup with compatible 17 mm hex wheels. With 2 adapters and matching small parts in the pack, both sides can be equipped with the same hardware format. The set suits workshop tasks such as replacing damaged wheel hex parts, refreshing a used drivetrain connection, or keeping matching spare fittings ready for the next maintenance session. Its compact format also makes it a practical addition to an RC parts box where axle hardware, pins and locking screws need to stay together as one coordinated set. Warning! Not suitable for children under 14 years.
Additional spares
Virus 4.0 Steering Linkage 2, RC spare part
500205929€9.99
The Virus 4.0 Steering Linkage 2 is a dedicated RC spare part for model-building enthusiasts who keep steering response precise through regular maintenance and targeted replacement. The set combines 2 metal turnbuckle-style rods, 4 black rod ends and 4 metal ball joint inserts into a compact linkage assembly for the steering system. The threaded rods allow the linkage length to be adjusted directly at the connection point, which helps when aligning the steering geometry on the Virus 4.0. The rod ends screw onto the metal links and provide the eyelet connections needed to join the steering hardware. Ball joint inserts sit inside these ends and create the pivoting movement required as the front steering mechanism changes angle in use. This combination of threaded metal parts and pivoting joints gives the assembly the functional structure needed for controlled steering input. On the bench, the set suits routine servicing, replacement of worn linkage parts or rebuilding a damaged steering connection on the model. The clearly defined component layout also makes it useful when restoring the original steering mechanism with matching hardware for the Virus 4.0 platform. Warning! Not suitable for children under 14 years.
Additional spares
Virus Akuma Gear Housing RC Spare Part
500205939€12.79
This gear housing is a dedicated RC spare part for Carson Virus and Akuma vehicles, designed for front or rear use where the drivetrain assembly needs the correct mounting structure again. The moulded form includes a circular bearing seat, reinforced contours and multiple fastening points that match the role of a structural housing inside the vehicle. Compatibility covers Virus 4.0, 4.1, 4.2, 4.3 and Race models, along with Akuma variants named in the product data, making this part relevant for targeted repair rather than generic workshop stock. The housing supports the placement of internal rotating components and provides the screw-mounted connection points needed for installation on the matching chassis area. Its dark moulded construction is shaped to enclose and support mechanical elements while keeping the assembly layout consistent with the original vehicle design. For hobbyists maintaining an existing RC platform, a model-specific replacement part helps avoid improvised fit solutions in a drivetrain rebuild. The part suits workshop tasks such as replacing a worn housing, rebuilding a damaged transmission area or preparing a compatible vehicle for running condition again. In a bench setup focused on service and reassembly, the defined mounting tabs and recessed screw positions support an orderly parts change within the matching Virus or Akuma platform. Warning! Not suitable for children under 14 years.
Additional spares
Virus Akuma Side Guards, RC spare parts
500405766€15.99
These side guards are a dedicated 2-piece spare part set for selected Carson Virus and Akuma RC vehicles. The set is built for the Virus 4.0, 4.1, 4.2, 4.3 and Race series as well as Akuma, giving model-building enthusiasts a direct replacement option for the outer chassis area when existing guards are worn, scraped or missing. The parts are formed as long matching side sections and, as shown by the visible mounting points, are made to attach to the vehicle with the correct hardware positions for the supported platforms. Their shape follows the side line of the chassis, covering the outer edge area with a clean, model-specific fit instead of a cut-to-size universal solution. This makes them useful for repair work after heavy running sessions, for restoring a used chassis, or for keeping a maintenance build consistent with the original layout. Age marking: 14 Years. In the workshop, a pair like this suits planned replacement during a strip-down or a quick swap when one side has taken damage. The 2-piece format provides the matching set needed for both sides of the vehicle, which helps keep the rebuild visually consistent across the chassis.
Additional spares
Virus-Ex Chassis, RC spare part, lower deck
500405959€65.99
The Virus-Ex Chassis lower deck is the structural base plate for an RC model car, built around a long molded form with pre-drilled mounting holes, recessed screw points, edge cutouts and an elongated centre slot. In the workshop, that layout creates a clear foundation for a repair, a parts replacement or a fresh chassis rebuild with the correct component positions already defined. Its flat undertray shape is designed to carry the core hardware of the vehicle, with space and fixing points for suspension components, drivetrain parts, electronics and body supports. The recessed screw areas help keep fastening points integrated into the plate, while the cutouts and slot add the clearance needed around mounted assemblies. Rather than acting as a generic sheet, this chassis piece serves as the central platform that determines how the running gear and installed equipment sit within the model. For hobby use, this spare part fits naturally into bench work where a damaged lower section needs replacement or an existing RC car is being rebuilt around a fresh base. The technical hole pattern and molded structure make it a focused choice for maintenance tasks on the Virus-Ex Chassis. Age marking: 14 Years. Warning! Not suitable for children under 14 years.
Additional spares
Virus/Akuma Servosaver-Unit, spare part
500205943€22.99
The servosaver unit for Virus and Akuma models is a dedicated replacement part for steering-related maintenance within the Carson Modelsport range. It is specified for Virus 4.0, 4.1, 4.2, 4.3 and Race as well as Akuma, giving model-building enthusiasts a defined fit across several compatible vehicle versions instead of a generic workshop substitute. The assembly shown combines shaped black parts with metal hardware and a coil spring, indicating the mechanical layout typical of a servosaver system that sits between servo action and steering linkage. That spring-loaded construction is used to absorb impact loads through the steering assembly and to bring worn or damaged hardware back into working order with the correct replacement group. As a spare part in the Models & Accessories area, it suits repair benches, routine maintenance and parts storage for existing RC vehicle fleets. Batteries are not included. In workshop use, the unit supports targeted servicing after heavy running sessions, contact damage or general wear in compatible Virus and Akuma vehicles. It also makes sense as a shelf spare for hobby setups that keep frequently used steering components ready for the next repair cycle. Warning! Not suitable for children under 14 years.
Additional spares
X 10 EB Dirtwarrior Sport Slipper Clutch Gear
500405574€16.99
The slipper clutch is a key part of an RC drivetrain, managing how motor force reaches the transmission under load. This X 10 EB Dirtwarrior Sport slipper clutch set gear is made as a dedicated spare part for the matching model and focuses on the mechanical core of the drive system rather than cosmetic add-ons. The assembly combines a large spur gear with a central mounted unit and comes with 2 retaining rings shown as part of the set. The visible threaded section and hex nut indicate the fastening point within the clutch assembly, while the forked ends and reinforced spoke layout define the structure of the mounted gear unit itself. For model-building enthusiasts, that makes this part useful when a worn drivetrain component needs a like-for-like replacement instead of a universal workaround. In workshop use, this kind of replacement part supports routine maintenance, rebuilds after heavy running, or the restoration of a vehicle that is no longer transferring power correctly. The 14 Years age marking is stated in the product data. Batteries are not included. Warning! Not suitable for children under 14 years.
Additional spares
X10EB Steering Unit Servosaver RC Spare Part
500405678€19.79
The X10EB Steering Unit Servosaver is a dedicated RC spare part set for rebuilding a compact steering subassembly with a spring-loaded protection mechanism. Black moulded arms, a flat linkage bar, ball studs, bushings and metal hardware come together as one steering unit, giving model-building enthusiasts the parts needed to restore the steering layout of the X10EB. At the centre of the assembly, the servosaver principle uses a coil spring, a metal threaded sleeve and a knurled ring nut to create controlled resistance within the steering system. This mechanical layout helps manage forces that travel through the linkage during running, while the ball studs and pivoting parts provide the connection points required for the steering movement itself. The set also includes long rods or pins, flanged inserts and small spacers that support the fit and function of the assembled mechanism. As a replacement assembly, it suits maintenance work, repair jobs and parts refreshes on an existing model. On the workbench, the separate components make this set a focused rebuild task for hobbyists who enjoy working directly on steering geometry and linkage hardware. In regular RC maintenance, it fits naturally into servicing after wear, impact damage or a planned mechanical overhaul of the X10EB steering area. Warning! Not suitable for children under 14 years.
Additional spares
XL Bumper Differential Housing Holder Spare Part
500405993€16.99
This spare part set is built around key replacement pieces for the Carson XL chassis and names the exact parts included in the data: bumper, differential housing cover, holder components and a spoiler mount. In a 1:10 chassis layout, these are the parts that connect exposed outer sections with mounting points around the drivetrain housing, making the set relevant when damaged fixings or worn covers need to be replaced. The combination of bumper hardware and differential housing parts keeps the repair focused on one defined area of the chassis rather than spreading across unrelated assemblies. The spoiler mount adds another model-specific fixing point from the same platform, which matters when restoring the body support layout after contact or breakage. The data also identifies the fit as XL chassis based, giving model-building enthusiasts a clear reference for workshop planning. Age marking: 14 Years. On the bench, this set suits targeted maintenance jobs where cracked mounts, stressed covers or missing holders interrupt the running condition of a 1:10 model. It also fits rebuild work on used chassis that need the named structural parts brought back into place before the next driving session.