Carson RC

Carson

Carson 1:10 Mega Duster Bundle

Product bundle consisting of: 1:10 Mega Duster 3.0 2.4G 100% RTR / 7,4V/2600mAh LiION batt. FE-Line XHP/TAM   Article number: 500404292 Product: 1:10 Mega Duster 3.0 2.4G 100% RTR Powerful racer for off-road action: The Carson FE Mega Duster 3.0 doesn't stop at any terrain! The independent suspension, full suspension and extremely grippy high-grip off-road tires make the vehicle ideal for unpaved terrain. The Mega Duster is ready to run and equipped with 1x 2.4 GHz remote control system, 2x Li-Ion drive battery (7.4 V/1500 mAh), 1x USB charger, 4x LR06 / AA transmitter batteries and detailed instructions. Fully charged and at full capacity, a full 25 minutes of driving time is possible. The LED lighting, digitally proportional control and waterproof RC components complete the overall package and make the model appear not only high-quality but also easy to handle. Under ideal conditions, the vehicle can reach top speeds of up to 30 km/h. Included: Fully assembled model, 2.4 GHz RC system, LiIon powerpack 7,4 V / 1500 mAh, charger, transmitter batteries, manual.     Article number: 500608307 Product: 7,4V/2600mAh LiION batt. FE-Line XHP/TAM Experience Maximum Power with Our 2600 mAh Li-Ion Tuning Battery! With 7.4 volts of output and a Tamiya connector, it delivers extended run time and is the perfect choice for the FE line. Get the performance boost you’ve been looking for – now!  

RC truggies & RC monster trucks

1:10 Mega Duster 3.0, RC car, 2.4 GHz RTR

The 1:10 Mega Duster 3.0 brings pick-up truck styling, LED lighting and a fully assembled RTR setup into a 430 mm off-road RC car built for rough ground. With independent suspension, coilover shocks and a fully suspended layout, the chassis is set up to absorb uneven surfaces while the multi-coloured printed body keeps the truck's desert-racer look clear in motion. Its 2.4 GHz radio system uses digital proportional control, so steering and throttle inputs can be fed in with fine adjustment rather than simple on-off commands. The included Li-Ion drive battery is rated at 7.4 V and 1500 mAh, and the USB charger is part of the set, along with 4 AA transmitter batteries. At 310 mm wide and 200 mm high, the truck carries a broad monster-truck footprint, while the stated weight of 1364 g supports a planted feel over gravel and dirt. Splash-proof electronics expand the running window when the surface is dusty or damp, and the stated driving time reaches up to 25 minutes. The Mega Duster 3.0 suits open ground, compacted trails and loose stone where the 115 mm all-terrain tires can work for grip and control. Age 14+ is stated for this model, and the fully assembled format gets the focus quickly onto driving lines, throttle control and off-road handling rather than workshop time.  Warning! Not suitable for children under 14 years.

RC cars

1:32 Deemon X, RC buggy, 100% RTR 2WD

€29.99

Compact scale and lively handling give the 1:32 Deemon X the feel of a true off-road RC buggy in a format built for quick runs at home or on small garden tracks. The 2WD layout, 2.4 GHz remote control system and selectable speed levels create a clear, responsive driving setup, while the elaborately printed body shell and switchable LED lighting keep the model visually sharp in motion. At 115 mm long, 86 mm wide and 53 mm high, the buggy fits neatly into tabletop courses, improvised obstacle lines and tighter turns where larger vehicles need more room. The 3.7 V 100 mAh LiPo drive battery supports up to 15 minutes of driving time, and recharging happens via the included USB charger. Included pylons and the jump ramp add concrete course elements for slalom sections, launch points and repeatable stunt practice rather than simple straight-line driving. The 69 g weight keeps the model nimble when changing direction, and the rubber tires give the chassis the grip needed for uneven surfaces. Short sessions on indoor floors, hallway tracks or paved garden paths suit the Deemon X especially well, whether the focus is clean cornering, quick acceleration bursts or ramp jumps. With 2 speed settings and a complete RTR package, the buggy moves easily between first RC laps and fast, compact course driving

Models & trailers

1:12 MB Unimog U300 THW, RC truck, 100% RTR

The Unimog line became known for compact dimensions, portal-axle capability and utility work across rough terrain, and that character carries into this 1:12 MB Unimog U300 THW RC truck. In blue THW livery, the model combines a 450 mm body length with a powerful electric motor, front LED lighting and a 2.4 GHz control system for controlled driving on paths, gravel and other uneven ground. Its 220 mm width and 260 mm height give the truck a tall, purposeful stance that suits the U300 shape, while the 2052 g weight adds substance in motion. The remote control handles steering and throttle proportionally, so small stick inputs translate into finer changes than simple on or off control. A separate horn function can be triggered from the transmitter, and motor sound control adds another layer to the driving scene. The 7.4 V 850 mAh Li-Ion drive battery is included, and the RTR setup also includes the 2.4 GHz transmitter, a USB charger and transmitter batteries. That combination suits first runs in the hobby as well as relaxed utility-style driving sessions with a scale vehicle theme. On compacted dirt, paving or loose gravel, the THW truck can be guided through tighter turns, short climbs and stop-start route changes while the illuminated front end keeps the model visually defined.

RC cars

1:10 Dustor, RC car, 2.4 GHz 100% RTR

€69.99

The 1:10 Dustor brings full-size RC presence to first runs and casual off-road sessions, with a 540 mm length, 300 mm width and 240 mm height that give the model a broad, planted stance on mixed surfaces. A brushed motor drives the 2WD rear-wheel-drive layout to speeds of up to 20 km/h, while the 2.4 GHz radio system reaches up to 75 m for clear control across open ground. Its fully assembled format keeps the focus on driving, and the included 7.4 V 500 mAh Li-Ion battery works with the USB charger for straightforward turnaround between sessions. At 985 g, the chassis stays light enough for responsive direction changes while still carrying the visual weight expected from a 1:10 off-road model. Front and rear impact protection support everyday running where gravel edges, kerbs and clipped markers are part of the route. The included transmitter is powered by 2 x LR06 AA batteries, so the full set is prepared for use without extra radio equipment. On asphalt, compacted paths or light terrain, the combination of suspension travel, rear-drive handling and off-road tires creates a controlled, approachable driving character. With up to 30 minutes of running time per charge, the Dustor suits park runs, open-yard driving and repeated practice laps where longer sessions matter.

RC tractors

1:16 Deutz-Fahr 8280 TTV, RC tractor, trailer

€99.99

The DEUTZ-FAHR 8280 TTV brings the look of a modern farm tractor into 1:16 scale with a matching trailer, 2.4 GHz radio control and working sound functions. Engine sound, horn and LED front lighting create a more lifelike driving scene, whether the tractor is rolling across loose soil, garden paths or a carefully arranged display setup. At 750 mm long, 180 mm wide and 234 mm high, the model has a substantial footprint that suits towing and transport play. The rigid axle supports off-road running, while the steering is tuned for precise control and a small turning radius, helping the tractor change direction cleanly and guide the trailer through tighter spaces. The officially licensed DEUTZ-FAHR styling carries the 8280 TTV identity into the bodywork, giving the model a recognisable agricultural character. The accessible battery compartment under the hood allows quick battery changes between runs. Included are the ready-to-run tractor with trailer, a 2.4 GHz remote control system, a 7.4 V 500 mAh Li-Ion drive battery, a USB charger and 2 x LR03 AAA transmitter batteries. With a weight of 1731 g and a driving time of 90 minutes, the set is equipped for extended driving sessions focused on towing, positioning and farm-style transport action.

RC lorries & RC trucks

1:20 MB Arocs Goldhofer, RC truck, 100% RTR

€109.99

Heavy-haul transport is a defining part of construction logistics, and the 1:20 MB Arocs Goldhofer brings that role into RC form with a 1000 mm long truck and low loader combination. The fully assembled RTR set combines remote-controlled driving with functional trailer handling, creating a model that looks at home moving machinery between workshop shelf and jobsite scene. At 155 mm wide and 185 mm high, the model carries the long, low stance of a transporter, while the 1350 g weight gives the combination a substantial feel in hand. The installed reversing light works automatically together with the tractor unit, adding a realistic response during manoeuvres without needing a separate command. Included in the set are the ready-to-run model, a 2.4 GHz RC system, 2 x 4.8 V NiMH batteries, a USB charger and 2 x AA transmitter batteries. The 30 minute driving time supports extended loading runs, repositioning moves and repeated coupling sequences. Minimum age: 8 years. The low-bed layout suits transport scenes with construction machinery or other scale loads, and the remote-controlled ramp and support add movement beyond simple forward driving. On a floor layout, workshop setup or construction-themed display, the MB Arocs Goldhofer turns loading, uncoupling and trailer positioning into the central part of the action.

Mini RC cars

1:60 Nano Racer Aston Martin V12 Vantage RC car

€17.99

The Aston Martin V12 Vantage brings a well-known British sports car shape into a compact 1:60 Nano Racer format with radio control and a red body that stands out clearly on small driving layouts. Its officially licensed appearance follows the full-size model closely, while the 79 mm length, 33 mm width and 22 mm height keep the car suited to short straights, table-edge turns and quick direction changes in limited space. The ready-to-run set includes the model, a remote control with charging connection, a 1.2 V 80 mAh NiMH drive battery, a screwdriver and instructions. The controller works on 2.4 GHz and reaches up to 15 m, giving the car enough room for indoor laps and compact obstacle courses. The same control system allows up to 50 vehicles to run simultaneously, which opens the door to group sessions without frequency clashes. With a weight of 25 g, the small chassis stays easy to handle between runs, and the battery delivers up to 10 minutes of driving time per charge. On a living room floor, a desk track or a small race setup, the Nano Racer format turns narrow spaces into usable circuits. Short driving sessions, quick charging through the controller and the compact footprint make this RC car a neat choice for spontaneous races, collecting and casual practice runs.

Mini RC cars

1:60 Nano Racer Fo.Must.ShelbyGT500, RC car

€17.99

The Ford Mustang Shelby GT500 has long stood for big-engine muscle car presence, and this 1:60 Nano Racer translates that character into a compact RC format. At 79 mm long, 33 mm wide and 22 mm high, the miniature car stays small enough for quick driving sessions on tables, smooth floors or improvised indoor courses while still carrying the licensed Ford look. The ready-to-run set includes the model, a remote control with charging connection, a 1.2 V 80 mAh NiMH drive battery, a screwdriver and instructions. The 2.4 GHz radio system gives the car responsive control and allows up to 50 vehicles to run simultaneously, which suits group races without frequency clashes. A 15 m control range leaves room for short sprints, turns and head-to-head runs, while the 25 g weight keeps the handling light and agile. The remote control also serves as the charging point, so the battery can be charged directly through the controller. With up to 10 minutes driving time, the Nano Racer fits quick race breaks, compact home circuits and repeated short sessions where several cars share the same space. The small footprint and simple control layout also make it easy to set up spontaneous races whenever a smooth surface is available.

RC buggys

1:8 Drakuro BL 3S, RC car, 4WD RTR

€299.99

The 1:8 Drakuro BL 3S RTR brings brushless power, long-travel suspension and a wide 370 mm stance into one large-scale RC car built for fast off-road running. At 500 mm long, 330 mm high and 3402 g in weight, the chassis carries real presence on dirt tracks, gravel stretches and open ground, with a top speed of up to 65 km/h. A longitudinal aluminum reinforcement brace adds rigidity through the centre of the chassis, and reinforced steel drive shafts at the front and rear transfer power under load. The waterproof 30 kg steering servo uses metal gears for direct steering input, while splash-proof electronics and housing support running in changing conditions. Height-adjustable body mounts make it easier to set the shell position cleanly over the chassis, and LED lighting at the front, rear and roof keeps the model clearly defined when the light drops. The XT90 high-current connector system is designed for low-loss power transmission within the drive setup. The ready-to-run package includes a 2.4 GHz remote control and instructions, so the focus stays on driving rather than sourcing the core control gear. With 14 Years marked in the data, the Drakuro suits high-speed bashing sessions, repeated acceleration runs and broad off-road lines where suspension travel, steering force and chassis size all come into play.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 M-B 200/8, RC car, 100% RTR trailer

€114.99

The Mercedes-Benz /8 series shaped everyday road traffic in the late 1960s and 1970s, and this 1:87 M-B 200/8 captures that classic saloon presence in a compact RC format. The green body and matching trailer combine a recognisable road-car silhouette with radio-controlled movement, creating a small-scale setup that carries both collector appeal and active driving use. Its 1:87 scale makes the model easy to place on a desk, shelf, or layout, while the trailer adds a second element that changes the overall scene and gives the combination a more complete towing look. The 100% RTR specification means the driving package is prepared for immediate use, and 5 included batteries cover the initial power requirement stated in the data. With a minimum age marking of 14 years, the model sits in a hobby-focused range rather than a preschool toy segment. The compact format also suits short driving sessions where a larger RC vehicle would need more floor space. Whether used for careful indoor manoeuvres, as a small addition to a model collection, or as a road-car counterpart within a miniature vehicle lineup, the M-B 200/8 with trailer brings motion into a classic passenger-car theme. The combination of saloon and trailer gives the setup a distinct identity both at rest and in operation.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 M-B Unimog U406, RC fire engine, RTR

€109.99

The Mercedes-Benz Unimog U406 has long been known for compact utility and all-terrain presence, and this 1:87 RC fire engine translates that character into a format built for close-quarters driving. Fine printing, high-quality paintwork and front and rear LED lighting give the body a convincing emergency-service appearance, while the very small turning circle suits narrow routes between scenery, tools or display pieces. The chassis uses 2WD rear-wheel drive and a brushed motor for controlled running, with fully proportional steering and acceleration allowing measured inputs instead of simple on-off commands. That control layout makes a visible difference on a desk, in a diorama or anywhere space is limited, because the model can be guided through tighter lines with cleaner corrections. The 2.4 GHz system supports stable operation, and the permanently installed 3.7 V 75 mAh Li-ion drive battery keeps the compact body free from bulky battery changes. Charging takes place via the transmitter and takes around 30 minutes. As a 100% RTR version, the set arrives with the remote control, the drive battery and the batteries required for the transmitter. Up to 60 minutes of driving time supports longer indoor sessions, whether the model is weaving through a small layout, tracing service routes across a tabletop or adding movement to a scale scene.

RC models in 1:87 scale

1:87 MB 1620 Tarp Truck, RC truck, 100% RTR

€139.99

The 1:87 MB 1620 Tarp Truck with trailer brings moving road traffic into H0 railway scenes with compact dimensions of 187 x 28 x 38 mm and fully assembled 100% RTR equipment. Official Mercedes-Benz Trucks licensing, fine printwork and the blue finish give this RC truck a recognisable presence beside stations, freight depots and urban track sections. Its 2.4 GHz radio system supports interference-free control and allows several models to run at the same time, which suits busy diorama setups with more than one active vehicle. The very small turning radius helps the truck work through narrow streets, loading areas and switching zones where larger RC formats would look out of scale. The trailer extends the road-train silhouette and the removable tarp changes the look of the load area for different scene concepts. Included in the set are the ready-to-drive model, 2.4 GHz remote control system, Li-Ion drive battery 3.7 V / 75 mAh, 4 transmitter batteries LR03 / AAA, and instructions. On a layout, the truck can roll alongside trains, serve as a delivery vehicle near a goods shed or move through a city section with controlled speed changes and steering inputs. Collectors can also place it as a static display piece, with the integrated driver figure and licensed cab details carrying the scale effect even when the model is parked.

RC helicopters

Eagle 280 Crash Stop, RC helicopter, 2.4G RTF

The Eagle 280 Crash Stop brings compact RC helicopter flying together with a front crash-stop sensor that reacts to obstacles by stopping and backing the model away. At 200 mm long, 280 mm wide and 125 mm high, this 56 g coaxial helicopter suits controlled flights in tighter spaces as well as calm outdoor use. The 2.4 GHz control system gives the model its dedicated radio link, while the emergency stop button on the transmitter adds a direct way to cut the action when needed. A 3.7 V 250 mAh LiPo flight battery powers flights of up to 7 minutes, and the model reaches speeds of up to 25 km/h. The aluminium chassis gives the structure a firm core, and the coaxial rotor arrangement supports balanced lift for measured handling. Spare rotor blades are included, so the set is equipped for continued running after routine contact or wear. Indoor flights near walls, hallways or furniture benefit from the forward obstacle response, while open areas allow short hovering runs, lift-offs and landings with the same compact airframe. The ready-to-fly package includes the helicopter, remote control system, USB charger and transmitter batteries, so the set is prepared for flight after the first charging process.

RC speed boats

RC Fire Boat 2.4G, RC boat, 100% RTR

The RC Fire Boat 2.4G 100% RTR brings firefighting action onto the water with a remotely operated water cannon, LED position lights and a sporty rescue-boat look. At 560 mm long, 147 mm wide and 215 mm high, the hull has a strong on-water presence, while the 2.4 GHz radio system keeps control stable across distances up to 100 m. The fully assembled boat is supplied as a ready-to-run set with a 7.2 V 1000 mAh NiMH drive battery, USB charger, 2.4 GHz remote control and 2 x AA transmitter batteries. Full driving functions cover forwards, backwards, left and right, so manoeuvres can be varied between straight sprints, tight turns and controlled repositioning for water-cannon play. A driving time of 45 minutes supports longer sessions before recharging, and the boat weight of 717 g keeps the format easy to handle between shore and water. Whether used on a pond, at the lakeside or on calm stretches of water, the fireboat combines radio-controlled driving with an extra action feature that changes how each run unfolds. Age 8 years+ marks the recommended age, and the included screwdriver supports the setup of the supplied components before the next launch.

Mini RC cars

1:60 Nano Racer Aston Martin V12 Vantage, RC car

€17.99

The Aston Martin V12 Vantage brings British sports car character into a 1:60 Nano Racer format, combining licensed body styling with compact RC handling. At 79 mm long, 33 mm wide and 22 mm high, the black coupe keeps a low, planted look that suits short sprints across tables, smooth floors and small driving spaces. Its 2.4 GHz radio system gives the model a dependable link to the controller across 15 m, and the layout also allows up to 50 vehicles to run at the same time. That makes the small scale especially lively in group sessions, where several cars can share the same area without constant frequency conflicts. The ready-to-run setup keeps the focus on driving, while the included 1.2 V 80 mAh NiMH drive battery matches the compact chassis and the 25 g weight for quick, light movement. Charging runs directly through the remote control unit, so the car and controller work as one neat driving system. With a maximum driving time of 10 minutes, the Nano Racer suits short races, repeat laps and quick head-to-head runs. Age 4+ is stated in the product data. The included screwdriver supports battery access as part of the set contents, and the compact format makes the model easy to store between sessions.

RC speed boats

RC Yacht Hurikan, RC boat, 2.4 GHz RTR

€39.99

The Hurikan brings yacht styling and fast RC handling together in a compact 350 x 95 x 105 mm format built for lively water runs. Sand tones, white surfaces and dark window graphics give the hull a sharp, modern look, while the 2.4 GHz radio system keeps steering input responsive during laps across the lake. At 270 g, the model stays light in the hand for carrying to the shoreline, yet its twin-prop drive gives the boat the thrust needed for brisk acceleration on the water. Full driving functions cover forward, backward, left and right control, making tight turns and quick corrections easy to manage. The set includes a ready-to-run model, a 2.4 GHz remote control system, a USB charger, 2 x LR06 AA transmitter batteries and 2 spare propellers. The included 3.7 V 1200 mAh Li-Ion battery powers sessions of up to 40 minutes, and the drive engages only in water through the integrated shut-off circuit. That combination suits calm-lake outings, pond sessions and repeated practice runs where clean response matters as much as speed. Age 8+ marks the recommended age, and the complete RTR setup keeps the focus on steering lines, throttle control and fast passes across open water.

RC cars

1:24 Lamborghini Sian, RC car, 2.4GHz RTR

€24.99

The Lamborghini Sian brings super sports car styling into a compact 1:24 RC format, pairing a low, sharply shaped body with radio-controlled handling and a full ready-to-run setup. With a length of 195 mm, a width of 80 mm and a height of 49 mm, the model carries its proportions in a size that suits quick laps across smooth indoor surfaces. The 2.4 GHz remote control system supports stable command input during solo driving, while the 3.7 V Li-Ion drive battery with 500 mAh powers up to 60 minutes of ride time. At 172 g, the car stays light in hand and easy to place on the floor between runs. The included USB charger keeps the charging routine simple, and the set also contains 2 LR03 AAA transmitter batteries. A rear axle differential adds a mechanical detail that supports smoother cornering behaviour, while steering fine adjustment helps tune the driving line to the available space. LED lights at the front and rear keep the bodywork visible when the room gets darker and add extra presence during evening driving sessions. On a hallway course, around furniture legs or across a cleared living-room track, the compact dimensions, quick responses and detailed Lamborghini look create a focused RC session with a clear sports car character.

Mini RC cars

1:60 Nano Racer Fo.Must.Shelby GT500, RC car

€17.99

The Ford Mustang Shelby GT500 has long stood for big-engine muscle-car presence, and this 1:60 Nano Racer translates that character into a compact RC format. With its licensed Ford design, red bodywork and stripe detailing, the small car brings a recognisable road-car silhouette to quick indoor driving sessions. The 2.4 GHz control system sends steering and throttle inputs over a range of 15 m, and it allows up to 50 vehicles to run simultaneously on the same frequency environment. Charging takes place through the remote control unit, which includes the charging connection for the 1.2 V 80 mAh NiMH drive battery. A full charge delivers up to 10 minutes of driving time. The ready-to-run format means the model, remote control with charging connection, NiMH drive battery, screwdriver and instructions are included. With dimensions of 79 x 33 x 22 mm and a weight of 25 g, the Nano Racer fits naturally into compact race setups where short straights, quick direction changes and close duels matter more than sheer size. The small scale also makes it easy to line up several cars for simultaneous runs, turning a table, hallway or smooth floor into a miniature racing scene with very little space required.

RC models in 1:87 scale

1:87 Mercedes-Benz O 302 DB, RC bus, 2.4GHz

€129.99

The Mercedes-Benz O 302 shaped coach travel across Europe for years, and this 1:87 RC bus brings that familiar silhouette into moving H0 scenes with licensed bodywork, raspberry red paintwork and front and rear LED lighting. At 112 mm long, 36 mm wide and 51 g in weight, the model sits naturally among buildings, platforms and road sections without overpowering the layout. Its 2WD rear-wheel drive works with a 2.4 GHz 3-channel radio system for controlled movement at up to 50 m, while the compact format helps the bus thread through tighter streets and station areas. The integrated 3.7 V Li-Ion battery with 75 mAh is built into the model, keeping the setup clean and the proportions true to scale. As a 100% RTR version, the set includes the remote control, the lithium drive battery, 4x AAA batteries, instructions and a storage case. The licensed Mercedes-Benz O 302 DB format gives the bus a recognisable road-going character that suits realistic transport scenes. On a model railway layout, the bus can roll between station forecourts, depot roads and town routes, adding controlled movement where static vehicles would otherwise remain fixed. The compact H0 scale format also suits shelf presentation between driving sessions, with the lighting and paintwork carrying the look of a classic DB bus into close-up display settings.

RC models in 1:87 scale

1:87 VW T1 SambaBus, RC car, 2.4GHz RTR

The VW T1 SambaBus with trailer brings classic touring style into compact RC form at 1:87 scale. The ready-assembled set pairs the iconic bus silhouette with a matching caravan, while front and rear LED lights add visible presence during each run. A 2.4 GHz remote control system handles the model with fully proportional inputs, so throttle and steering respond in fine steps rather than simple on or off commands. Steering trim helps keep the vehicle tracking cleanly, especially on narrow routes and detailed miniature layouts. The 3.7 V 75 mAh Li-Ion drive battery supplies the power, and the transmitter also serves as the charging connection with a 60 minute charge time. The compact format and very small turning radius suit controlled driving in limited space where broader models would need more room. The combination of SambaBus and caravan creates a distinctive road-trip scene for shelf display, diorama use or active driving sessions. Included in the set are the ready-to-run model, the 2.4 GHz remote control system, the Li-Ion drive battery and 4 AAA transmitter batteries, so the model is equipped for use straight from the set.  Warning! Not suitable for children under 14 years.

RC aircraft

Easy Skydreamer, RC aircraft, 2.4 GHz RTF

€29.99

The Easy Skydreamer brings a compact flying-wing layout, twin propellers and 2.4 GHz control into a light RC aircraft that is built for straightforward handling in open-air flying sessions. At 240 mm long, 240 mm wide and just 20 g in weight, the airframe combines a small footprint with a notably light feel that suits quick launches and controlled passes. Its 6-axis gyroscope works continuously in the background to steady the model in flight, giving steering inputs a calmer, more predictable response than an unstabilised layout. The Flexipor airframe adds another concrete advantage: the material keeps the structure light while coping well with the bumps that can come with early practice flights. Twin rear-mounted propellers support the aircraft's powered flight concept, and the included 3.7 V 150 mAh LiPo flight battery supplies up to 15 minutes of runtime per charge. The set is configured as 100% Ready to Run, so the core flying hardware is already matched for use. Included in the set are the flight-ready model, the remote control, the LiPo flight battery, a USB charger, 2 x LR06 transmitter batteries and 2 spare propellers. With its stabilised control concept and low 20 g weight, the Easy Skydreamer suits park flights, first RC take-offs and short practice sessions focused on smooth turns, level passes and repeatable landings.

RC helicopters

Easy Tyrann 200 Boost IR, RC helicopter, 100% RTF

€29.99

The Easy Tyrann 200 Boost IR brings compact indoor helicopter flying into a 100% RTF format with a 240 mm body, 200 mm rotor diameter and a 3-channel infrared control system. Its gyro-supported flight stabiliser helps keep the model composed in the air, while the switchable boost function adds an extra burst of power when the pace needs to change. A 3.7 V LiPo flight battery with 250 mAh capacity powers flight times of up to 9 minutes, and charging runs through the included USB charger. The transmitter also controls the color changing LED, so the light effect can be switched during flight rather than staying fixed. With a top speed of 15 km/h and a flight weight of 31 g, the helicopter stays light enough for controlled indoor use while still delivering lively movement. The ready-to-fly set includes the model, IR remote control system, LiPo flight battery, USB charger, 3x LR06/AAA transmitter batteries and spare rotor blades. Short hovering runs in a living room, careful turns along a hallway or repeated take-offs and landings on a smooth floor all suit the compact format. Age 8 Years+

Models & trailers

1:12 MB Unimog U300, RC truck, 100% RTR

The MB Unimog U300 has long been known as a compact utility truck with strong off-road credentials, and this 1:12 RC version carries that working character into a fire brigade layout with covered rear bed, roof beacons and front LED lighting. At 450 mm long, 220 mm wide and 260 mm high, the model brings a substantial road presence while staying manageable for regular driving sessions. The fully assembled chassis is ready to run with a powerful electric motor, digital proportional control and a 2.4 GHz remote control unit. Steering and throttle inputs can be adjusted progressively, which gives the truck a more controlled feel than simple on or off commands when lining up turns or easing over rougher ground. The included 7.4 V 850 mAh Li-Ion drive battery supplies up to 60 minutes of driving time, and a USB charger is part of the set. Horn and motor sound can be triggered from the transmitter, adding another layer of interaction during runs. With a vehicle weight of 2052 g, the model has enough substance to suit its utility-truck character. Fire brigade markings, the covered cargo area and the upright Unimog proportions make this RC truck fit naturally into rescue-themed driving scenes, yard layouts or obstacle courses with gravel, paving and mixed surfaces. The included transmitter batteries complete the 100% RTR setup, so the model can head straight into its first run after charging.

Mini RC cars

1:50 Nano City Dump Truck, RC truck, 2.4 GHz

€18.99

Construction trucks have long shaped city streets and building sites with their compact strength and unmistakable working profile. The 1:50 Nano City Dump Truck brings that familiar form into a small RC format with a true-to-original design, a detailed driver's cab and a ready-to-run setup for immediate use. Its fully assembled layout keeps the focus on driving, while the 146 g weight and 135 mm length create a handy format for controlled manoeuvres on tables, floors or improvised indoor routes. The open dump body gives the model its recognisable utility-truck silhouette, and the non-slip rubber tires provide the grip needed for cleaner starts, tighter turns and steadier movement on smooth surfaces. The 2-channel 2.4 GHz radio system supports interference-free control, which is especially useful when several radio-controlled models are active nearby. LED lighting adds another working-vehicle detail and makes the truck easier to track when the route runs through dimmer corners. Included in the set are the ready-to-run model, a 2.4 GHz remote control, a 3.7 V 500 mAh Li-Ion drive battery, a USB charger and instructions. With up to 40 minutes of travel time, the compact dump truck suits quick driving sessions, small construction-themed layouts and repeated laps through indoor obstacle courses.

RC models in 1:87 scale

1:87 M-B Unimog U406, RC truck, 100% RTR

€114.99

The Mercedes-Benz Unimog U406 has long stood for compact utility vehicle engineering, and this 1:87 RC version carries that character into a small-format driving model with a matching trailer. In bright orange with detailed paintwork and precise printing, the Unimog combines a true-to-original look with compact radio-control technology for controlled runs across a desk layout, a diorama road or a small indoor course. The 2.4 GHz remote control is part of the 100% RTR setup, so the model arrives with the core driving equipment already matched to the vehicle. Front and rear LEDs work alongside the switchable warning light to sharpen the service-vehicle appearance during operation. Steering trim on the transmitter helps fine-tune straight running, which is especially useful at 1:87 scale where small corrections show clearly. The permanently installed Li-Ion battery is rated at 3.7 V and 75 mAh, and the set also includes the required transmitter batteries plus a storage case for transport and tidy shelf keeping. The trailer broadens the operating scene beyond simple laps, with a tilting bed and removable tarpaulin that suit loading and unloading setups in miniature worksite or farm-style layouts. With age recommendation 14 years and up, the model fits hobby sessions focused on compact manoeuvres, display layouts and detailed vehicle handling in limited space.

RC yachts

Bella Luisa 2.4G, RC boat, 100% RTR

€69.99

Classic runabout styling meets radio-controlled action in the Bella Luisa 2.4G 100% RTR. The 455 mm motorboat combines a glossy wood-look finish, a clear curved windshield and chrome-look deck details with full steering control, creating a striking presence on ponds and small lakes. The hull measures 455 x 105 x 140 mm and weighs 648 g, giving the boat a slim, low profile on the water. Inside the set are a 2.4 GHz transmitter, a 7.4 V 1200 mAh Li-Ion drive battery, a USB charger and 4 AA transmitter batteries, so the model is fully assembled and ready for operation. The propeller drive reaches up to 10 km/h, while the water-activated motor start means the propeller engages only when the boat is on the surface. The detailed fairing and driver's cabin shape add to the leisure-boat look, and the cockpit area offers space for a play figure. On a calm garden pond, the responsive left-right and forward-reverse controls support neat manoeuvres along the bank or broad passes across open water. A driving time of up to 25 minutes leaves room for longer sessions before the battery returns to the USB charger.

RC speed boats

Sea Ray 2.4 GHz, RC boat, 100% RTR

€54.99

The Sea Ray 2.4 GHz brings twin 380 brushed motors, a streamlined hull and RTR convenience together in a compact RC boat built for fast action on the water. At 395 mm long, 190 mm wide and 100 mm high, it cuts a neat profile across ponds and calm lakes, with LED lighting adding a clear visual accent as the hull moves through changing light. The fully assembled format keeps the focus on driving rather than setup, and the included 7.4 V 600 mAh Li-Ion battery supports up to 20 minutes of running time per charge. A charging time of 3 hours keeps the routine straightforward between sessions. The 2.4 GHz radio system is designed for 1 player control, while the water-protected receiver and battery box help keep key electronics covered from spray. A built-in shut-off means the motors only run in water, matching the boat's intended use with a clear functional safeguard. Its lightweight 349 g build makes carrying the model from bag to bank easy, and the compact shape sits comfortably in hand at launch and recovery. With 2 AA transmitter batteries included, the set is ready for immediate use in suitable water conditions, whether the plan is short speed runs, repeated passes along the shoreline or relaxed practice with steering and throttle control.

RC aircraft

Stinger 2.0 2.4GHz 100% RTF, RC airplane

€49.99

The Stinger 2.0 2.4GHz 100% RTF brings a light 29 g airframe, intelligent gyro electronics and a ready-to-fly setup into one compact RC airplane built for controlled first flights and relaxed repeat sessions. With a length of 315 mm and a width of 385 mm, the model carries a broad wing layout that gives the aircraft a clear presence in the air while keeping the format easy to transport to open flying spaces. The Flexipor construction keeps weight low and supports the light handling that suits this class, while the 2.4 GHz control system allows clean command input without cable setup. A 3.7 V 300 mAh LiPo battery powers the airplane, and charging runs through the included USB charger. Spare rotor blades are included for continued use after routine wear, and the included 2x AA batteries complete the transmitter power supply. The gyro system works with the control inputs to calm the model in flight, which helps maintain a steadier line during climbs, gentle turns and landing approaches. Open ground, a sports field or another suitable flying area gives the 385 mm wingspan room to work through smooth passes and repeated take-offs. The ready-to-fly format keeps preparation focused on charging, switching on and heading into the next 20-minute flying session.

RC truggies & RC monster trucks

1:10 Bokusa BL 2S 4WD RTR, RC car, yellow

€219.99

The 1:10 Bokusa BL 2S 4WD RTR brings brushless power and monster truck stance into a ready-to-run RC car built for fast off-road sessions. Its 455 x 312 x 180 mm format and 2165 g weight give the chassis a planted footprint, while the yellow body adds a bold trackside look. A 30 kg waterproof steering servo with metal gears handles steering input with firm control, and the fully ball bearing mounted transmission supports efficient running across the drivetrain. Metal differentials at the front and rear use steel bevel gears, adding a solid mechanical base for repeated acceleration and braking. The 2.4 GHz remote control system is included, and the radio system is water-protected for running in changing ground conditions. An XT90 high-voltage battery connector system and a quick-change battery mount keep battery swaps straightforward between sessions. With a stated runtime of up to 15 minutes, the model suits short, fast runs on dirt, gravel and uneven surfaces where suspension travel and tyre grip can be used fully. Age 14 Years. A battery is required separately.  Warning! Not suitable for children under 14 years.

RC truggies & RC monster trucks

1:10 XS Tekuro, RC car, 100% RTR 4WD

€199.99

The 1:10 XS Tekuro brings a fast off-road setup into a ready-to-run format, combining permanent 4WD, a high-torque 550 brushed motor and up to 40 km/h for lively runs across dirt, gravel and rough ground. At 410 mm long, 300 mm wide and 175 mm high, the chassis carries a broad monster-truck stance that suits uneven terrain and quick direction changes. Completely mounted on ball bearings, the drivetrain is built to reduce drag through the transmission, while metal differentials at the front and rear use steel bevel gears for direct power transfer under load. The XT60 high-voltage battery plug-in system supports a secure connection for the included 7.4 V 2600 mAh Li-Ion battery pack, and the quick-change battery holder keeps swaps straightforward between sessions. Weight comes in at 1741 g, giving the chassis enough mass to stay settled as the suspension works through bumps. The rear bumper integrates a wheelie bar that supports controlled lift when the motor loads up hard from a standing start. The scope of delivery includes the 100% RTR model, 2.4 GHz remote control system, 2600 mAh 7.4 V drive battery, 1 A USB charger, 4 LR06 AA transmitter batteries and a manual. Driving time is about 15 minutes, making the XS Tekuro a strong fit for park runs, compact off-road tracks and loose-surface sessions where quick setup and solid traction matter.  Warning! Not suitable for children under 14 years.

RC cars

1:12 Glow Rider, RC buggy, 2.4 GHz RTR

€54.99

The Glow Rider brings 1:12 RC buggy action together with vivid LED lighting, creating a strong visual presence when the track gets darker and the body starts to glow in motion. At 340 x 215 x 123 mm and 570 g, the model combines a compact footprint with a planted off-road stance that suits quick direction changes and fast evening runs. The 2.4 GHz control system supports multiplayer driving without the close-range interference common to older frequency setups, which helps keep each buggy responsive during shared sessions. Full suspension works beneath the low body shell to absorb uneven ground and keep steering inputs more consistent over rougher surfaces. Grippy off-road tyres add traction where loose dirt, gravel or short grass would unsettle a road-focused setup. The ready-to-run package includes the assembled model, a Li-Ion drive battery, a USB charger and 2 AA transmitter batteries, so the full driving setup is in the box from the start. Age recommendation: 8 years and up. A paved yard at dusk, a compact dirt section in the park or a smooth evening track all suit the Glow Rider well, especially when the illuminated body can stand out against lower light. Up to 25 minutes of driving time at full capacity gives each session enough length for repeated laps, quick races and steady practice with throttle and steering control.

RC tractors

1:16 Deutz-Fahr Tractor 8280 TTV, RC tractor

€84.99

The DEUTZ-FAHR 8280 TTV is recreated here as a 1:16 RC tractor with a detailed body, realistic driving functions and a strong farm vehicle presence. At 400 mm long, 180 mm wide and 234 mm high, the model carries the proportions of the original into a format that suits both active driving and shelf display. The ready-to-run set includes the tractor, a 2.4 GHz remote control system, a 7.4 V 500 mAh Li-Ion drive battery, a USB charger and 2 transmitter batteries. Engine sound and horn add direct control inputs beyond steering and throttle, giving each run a more lifelike operating feel. The licensed DEUTZ-FAHR design is supported by cab details, body shaping and the characteristic tractor layout. With 5 frequency channels, the radio system provides stable control for solo driving sessions. Driving time reaches up to 90 minutes, allowing longer runs before recharging. On the floor at home, along a garden path or across lightly uneven ground, the compact dimensions and rigid axle help the tractor stay composed as it changes direction and tracks through tighter sections. Age 8 years+ marks the recommended age for use.

RC diggers

1:16 Volvo EC 160E, RC excavator, 100% RTR

€199.99

The Volvo EC 160E brings excavator handling into 1:16 scale with a ready-to-run RC setup, a true-to-original driver's cab and a working crawler layout built around 2 separately driven chains. With an operating weight of 2354 g and dimensions of 252 x 168 x 180 mm, the model carries a substantial presence while remaining manageable for controlled indoor driving and digging sessions. Its function package focuses on coordinated arm work rather than simple forward travel. The lifting arm and stick are made of plastic, and the spindle drive system moves the lifting arm, stick and bucket through deliberate, mechanical action that suits loading, lifting and placement tasks. The 2.4 GHz radio system supports single-user control, and the maximum operating time of up to 190 minutes allows longer work cycles before recharging. The included sheet metal shovel, scrap grab and excavator chisel shift the machine from earthmoving to gripping and breaking scenarios without changing the core vehicle. On a floor-based building site layout, the excavator can turn the uppercarriage through 360° to pick up, swing and place material within a compact work zone. The RTR package includes the model, remote control system, 7.4 V 1200 mAh Li-Ion drive battery, 3 LR06/AA transmitter batteries and instructions.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 VW T1 Pritsche, RC car, green trailer

€104.99

The VW T1 became one of the defining light commercial vehicles of the post-war era, and this 1:87 RC version captures that familiar silhouette in a compact format with a green car trailer behind it. The radio-controlled layout turns the classic VW T1 Pritsche into a moving scale model that combines display character with active handling on a small footprint. Its 1:87 scale makes the model easy to place on layouts, shelves, or desks where larger vehicles would need far more room, while the trailer adds a second visual element that extends the transporter theme beyond the cab itself. The green finish gives the combination a clear, period-inspired presence, and the Pritsche body style keeps the utility look of the original vehicle at the centre of the design. As a powered ground vehicle, it brings motion to a format often chosen for static collecting, which changes how the model can be used between display moments and controlled runs. 5 batteries are included. The age marking is 14 Years. The compact dimensions implied by 1:87 scale suit short driving sessions on smooth indoor surfaces, model layouts, or table-based scenes where precise movement matters more than outright speed. It also fits neatly into collections built around classic transport themes, especially where a trailer combination adds extra visual interest without taking over the whole scene.

RC quadcopters

Cyber Drone Polizei, quadcopter, 2.4G RTF

€34.99

The Cyber Drone Polizei 2.4G 100% RTF brings compact quadcopter flying into a ready-to-fly format with a 2.4 GHz remote control, a 3.7 V 600 mAh LiPo battery and a USB charger. With a length of 125 mm, a width of 135 mm, a diameter of 150 mm and a rotor diameter of 45 mm, the layout stays light at 50 g ascent weight and suits quick take-offs in smaller open spaces. Its control setup combines several functions that shape how the model behaves in the air. The 8 minute flight time supports short, focused rounds, while the included transmitter power uses 3 AAA batteries. The headless mode changes orientation handling by referencing the control direction rather than the nose position, which helps keep steering inputs easier to read during turns. Trim adjustment for left and right flight allows finer correction when the quadcopter drifts off line. Blue and red flashing LEDs remain easy to spot once the model lifts away from the launch point. Ready-to-fly equipment keeps the set focused on getting airborne with minimal preparation, whether the session starts on a driveway, in a yard or across a calm section of park ground. The compact dimensions, return function and selectable speed levels make it easy to alternate between steady hovering, directional practice and quick stunt passes in the same outing.

RC cars

Magic Machine 2.0, RC car, 2.4 GHz RTR

€49.99

The Magic Machine 2.0 brings a striking twist to RC driving with a body that changes function at the touch of a button. In one moment it runs as a flat racer, and in the next it shifts into an off-road configuration with more ground clearance, creating a fast change of character on asphalt, ramps and rougher sections. Its layout combines separately steered front and rear units with all-wheel drive, so both axles work together as the vehicle changes direction. That unusual steering concept gives the model its own driving feel and supports quick reactions when obstacles appear in the path. The body design also allows the machine to flip backward over obstacles, continue driving on its back and right itself again to keep moving. LED lighting adds another visible detail during use, while the contrasting top and bottom styling makes each rollover part of the visual effect rather than a stop in the action. With a length of 340 mm, a width of 215 mm and a height of 123 mm, the model has a compact footprint matched by a weight of 570 g. The included Li-Ion drive battery delivers up to 25 minutes of driving time and is paired with a USB charger. A 2.4 GHz remote control in a game controller style is included, along with 2 AA transmitter batteries, so the ready-to-run set is equipped for immediate use after charging.

RC truggies & RC monster trucks

1:10 Bokusa BL 2S, RC car, 4WD RTR

€219.99

The 1:10 Bokusa BL 2S brings brushless power, 4WD traction and RTR convenience into a 455 mm off-road machine built for fast, dirt-focused running. With a width of 312 mm, a height of 180 mm and a weight of 2165 g, the chassis carries a broad, planted stance that suits rough ground and quick direction changes. Metal differentials at the front and rear use steel bevel gears to distribute drive across the axle line, while the fully ball bearing mounted transmission supports efficient running through the drivetrain. A 30 kg waterproof steering servo with metal gears gives the front end firm steering authority in wet or dusty conditions, and the water-protected 2.4 GHz remote control system keeps control input stable during outdoor sessions. The XT90 high-voltage battery connector system is paired with a quick-change battery mount, so battery swaps stay straightforward between runs. Age recommendation: 14 years and over. As an RTR model, the Bokusa BL 2S is set up for immediate driving once the required power source is added. Gravel tracks, compacted dirt and uneven open ground suit the suspension layout and tyre format especially well, while repeated acceleration runs benefit from the wheelie bar at the rear. Batteries are required separately.  Warning! Not suitable for children under 14 years.

RC truggies & RC monster trucks

1:10 XS Ryken, RC buggy, 100% RTR 4WD

€199.99

The 1:10 XS Ryken brings fast off-road running into a compact RTR format, pairing a 550 brushed motor with permanent 4WD for direct launches and steady pull across mixed terrain. At 410 x 300 x 175 mm and 1741 g, the buggy carries a broad, planted stance that suits dirt tracks, gravel paths and uneven ground. Power reaches the wheels through hardened steel drive shafts and a central steel cardan shaft, while front and rear metal differentials with sealed steel bevel gears keep the drivetrain precise under load. A chassis mounted on ball bearings supports efficient running, and the splashproof housing and electronics keep light rain and wet ground from stopping the session. The rear wheelie function uses targeted torque and traction control to lift the front end under acceleration, adding a distinct driving character beyond straight-line speed. A rear spoiler and rollover cage complete the body with added protection for the shell and electronics during tip-overs. The 100% RTR setup arrives pre-assembled with a 2.4 GHz remote control system, a 7.4 V 2600 mAh drive battery, a 1 A USB charger and 4x LR06/AA transmitter batteries. That makes the XS Ryken ready for immediate running on open ground, from compact backyard courses to rougher off-road stretches where grip, suspension travel and drivetrain control all come into play.  Warning! Not suitable for children under 14 years.

RC truggies & RC monster trucks

1:10 XS Ryken, RC car, 100% RTR 4WD blue

€199.99

The 1:10 XS Ryken brings off-road action into a 410 mm long RC car with a wide 300 mm stance, 175 mm height and a ready-to-run setup built for immediate driving. Its blue body sits over a layout tuned for rough ground, where the combination of 4WD and generous clearance gives the chassis the grip needed for loose tracks, uneven paths and dusty sections. Power comes from a 550 brushed motor paired with a 7.4 V 2600 mAh Li-Ion drive battery, delivering up to 40 km/h and around 12 minutes of driving time. The hardened steel drive shafts transfer power with minimal play, while the sealed steel differential gears support clean, direct drivetrain response when dirt and vibration build up. The integrated wheelie function adds a distinct handling character by managing torque and traction so the front end can rise under acceleration. Oil-damped suspension helps the car settle after bumps and keeps the tyres working across broken surfaces. As a 100% RTR model, the set includes the ready-to-run vehicle, a 2.4 GHz remote control system, the drive battery, a 1 A USB charger and 4x LR06/AA transmitter batteries. With a weight of 1741 g, the chassis carries enough presence for stable running on open ground, gravel stretches and wet outdoor surfaces where splashproof electronics matter.  Warning! Not suitable for children under 14 years.

RC cars

1:14 Lam.Murcielago SV2.4G, RC car, 100% RTR

€54.99

The Lamborghini Murcielago SV translates the dramatic lines of the full-sized supercar into a 1:14 RC model with compact road presence and strong visual detail. At 330 mm long, 145 mm wide and 80 mm high, the body carries opening doors and a lifting hood that add hands-on interaction beyond pure driving. The detailed interior gives the cabin more depth when the body is viewed up close, while the front and rear LED system keeps the silhouette readable in lower light. A differential gear manages the drive effect between the wheels during turns, which helps the model hold a cleaner line through changing corners. Fully sprung suspension adds another mechanical layer, allowing the chassis to settle more evenly as the surface changes. The model weighs 631 g, giving it a planted feel in motion without losing the agile character expected from this scale. The fully assembled 100% RTR format keeps the focus on driving rather than setup, with a 2.4 GHz remote control unit included in the set. Also included are the 7.4 V 500 mAh Li-Ion drive battery, a USB charger and 2 x LR06 batteries. Driving time reaches up to 25 minutes, making the model well suited to repeated laps, short handling sessions and display breaks between runs.

RC buggys

1:8 Drakuro BL 3S 4WD RTR, RC car

€299.99

The 1:8 Drakuro BL 3S 4WD RTR brings brushless power, long-travel suspension, and a wide off-road stance into a ready-to-run RC car built for fast runs across mixed terrain. With a length of 500 mm, width of 370 mm, height of 330 mm, and weight of 3402 g, the chassis carries the planted footprint needed for high-speed driving and rough-surface control. A waterproof 30 kg steering servo with metal gears gives the front axle the force needed for direct steering inputs, while splash-proof electronics and housing support running where dust, spray, and loose dirt are part of the session. Steel differentials at the front and rear distribute drive through the drivetrain, and height-adjustable body mounts allow the shell position to be matched to the setup. The XT90 high-current connector system is designed for low-loss power transmission, supporting the demands of the brushless drive package under load. LED lighting at the front, rear, and roof keeps the body easy to track as conditions darken, and the rear bumper integrates a wheelie bar for hard launches under strong acceleration. The ready-to-run set includes a 2.4 GHz remote control and instructions. 14 Years marks the recommended age.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 Volkswagen Beetle, RC car, 2.4 GHz RTR

Few cars carry the visual identity of the Volkswagen Beetle as clearly as this 1:87 RC version in red. The rounded body shape, detailed paintwork and decoration, and illuminated front and rear LED lights bring the classic silhouette into motion on a compact scale. The ready-to-run set includes the assembled model, a 2.4 GHz remote control system, a 3.7 V 40 mAh Li-Ion drive battery and 4 AAA transmitter batteries. Fully proportional control allows measured throttle and steering inputs instead of simple on-off commands, which gives the small chassis a more precise feel in confined spaces. Steering trim on the transmitter supports straight tracking when fine corrections are needed. The transmitter also handles charging, with a 45-minute quick-charge time matched by a driving time of up to 45 minutes. A storage showcase is included for keeping the model protected between runs. With its very small turning radius, the miniature Beetle suits short indoor routes, desk-side driving and detailed diorama settings where tighter corners matter. The 1:87 scale also makes it a strong fit for collectors and model-layout enthusiasts who want a drivable classic car with compact dimensions and a finished RTR setup.

RC models in 1:87 scale

1:87 VW Beetle, RC car, trailer, 2.4 GHz RTR

€114.99

The Volkswagen Beetle became one of the most recognisable car shapes of the 20th century, and this 1:87 RC version pairs that silhouette with a matching trailer for a compact driving set with strong period character. Detailed paintwork and decoration, front and rear LED lights, and the rounded body lines give the miniature a clear display presence even when parked between runs. Its 2.4 GHz radio system uses fully proportional control, so steering and throttle inputs can be adjusted smoothly instead of switching only between stop and full power. Steering trim helps fine-tune straight running, and the very small turning radius suits narrow routes on desks, shelves or indoor floors where larger RC models need more space. The included 3.7 V 40 mAh Li-Ion drive battery keeps the format compact, and the transmitter handles charging in 45 minutes. A storage showcase is included for presentation between driving sessions, and the set is marked 14+. The trailer adds a second moving element to the setup, changing the handling feel as the Beetle pulls a compact load through bends and turnarounds. Short evening runs, shelf display, or a small tabletop course all suit the 1:87 format, with the illuminated front and rear sections staying easy to spot as the model moves through tighter spaces.  Warning! Not suitable for children under 14 years.

RC quadcopters

Cyber Drone IR RTF, quadcopter, 360° flips

€25.99

The Cyber Drone IR RTF brings compact quadcopter flying into a nimble 125 mm x 135 mm format with a 150 mm diameter and a 45 mm rotor diameter. A button-triggered 360° flip function adds fast aerial action, while the Coming Home function returns the quadcopter to its home point at the touch of a button, creating a clear, easy rhythm between short flights and recovery. Its 3.7 V/600 mAh LiPo flight battery supports up to 8 minutes of flight time, and the 50 g ascent weight keeps the model light in the air. The IR control concept is paired with 3 speed settings, so the handling can stay measured for early practice or become more lively for tighter reactions. Blue LED lighting adds clear visual orientation once the quadcopter lifts off, especially when the frame is moving quickly through flips, turns and short climbs. The green finish gives the model a bright, high-contrast look in motion. Short sessions in the living room, open indoor areas or calm practice runs with repeated take-offs and landings all suit this ready-to-fly setup. Included contents are the ready-to-fly model, IR remote control, LiPo flight battery 3.7 V/600 mAh, USB charger and instruction manual.

RC speed boats

RC Boot Rescue 2.4G, RC boat, ready to run

€39.99

The RC Boot Rescue 2.4G brings rescue-boat styling and quick radio-controlled handling together in a compact 350 mm format. The red and yellow hull, raised cabin and roof light details create a clear emergency-service look on the water, while the 2.4 GHz control system keeps commands responsive during fast passes and tighter steering inputs. At 95 mm wide and 105 mm high, the boat combines a slim profile with a stable stance for controlled manoeuvres. Forward, backward, left and right control allows precise handling around pool edges, small obstacles and turning points. The fully assembled model comes as a ready-to-run set with remote control, a 3.7 V 1200 mAh Li-Ion battery, a USB charger and 2 x LR06 AA transmitter batteries. With a weight of 270 g, the hull stays easy to carry to the water and simple to set down for the next run. The water-activated circuit keeps the drive inactive on land and switches operation on only in water. Up to 40 minutes of running time supports longer sessions at the pond or in a larger pool, and the 2 spare propellers add a practical replacement set for regular use. Age recommendation: 8 years+

RC cars

1:10 Cage Fighter, RC buggy, 2.4GHz RTR

€74.99

The 1:10 Cage Fighter brings desert buggy styling, radio-controlled handling and ready-to-run convenience into one fast-moving off-road setup. As a fully assembled RC buggy with 2.4 GHz control, it heads straight into dirt tracks, packed gravel and open ground with a low barrier to entry and a focused motorsport feel. Its full suspension supports precise steering response when the surface turns uneven, while the grippy off-road tyres help the buggy hold traction across changing terrain. Solid bumpers at the front and rear add protection in the zones that take the hardest knocks during close running. At 436 mm long, 234 mm wide and 147 mm high, the chassis has a planted footprint that suits outdoor driving, and the 806 g weight keeps the model agile in direction changes. The included Li-Ion drive battery runs at 7.4 V with 500 mAh capacity, and the set also includes a USB charger, a 2.4 GHz remote control and 2 x LR06/AA transmitter batteries. Top speeds of up to 18 km/h add a brisk pace without pushing the model beyond approachable control. Whether the route runs over compacted soil, short grass or rougher backyard ground, the Cage Fighter is built for active RC sessions rather than shelf display. Age 8+ marks the recommended age, and the 100% RTR format keeps the focus on charging the battery, taking the controller in hand and getting the buggy moving.

RC cars

1:10 Cage Fighter, RC buggy, 2.4GHz RTR

€74.99

The 1:10 Cage Fighter brings fast off-road RC action into a ready-to-run format with a fully assembled chassis, 2.4 GHz radio control and a 7.4 V 500 mAh Li-Ion drive battery. At 436 mm long, 234 mm wide and 147 mm high, the buggy cuts a planted stance as it charges over dirt, gravel and uneven ground. Its full suspension helps the wheels stay in contact with the surface, so steering inputs translate into cleaner direction changes instead of skittish bouncing. The 806 g vehicle weight supports an agile feel without losing presence on the track. Front and rear bumpers frame the chassis with added protection in the zones that meet obstacles first, which suits repeated running in tighter spaces and rougher outdoor sections. The included USB charger keeps the battery routine straightforward, and the supplied 2 x LR06 AA transmitter batteries complete the set. With a driving time of 25 minutes and speeds of up to 19 km/h, the Cage Fighter suits short backyard sessions, improvised dirt courses and casual head-to-head runs with other 2.4 GHz models. Age 8+ is stated for this RC buggy, making it a strong entry point into radio-controlled driving while still offering enough pace and control to stay engaging beyond the first outings.

RC cars

1:10 Night Racer 2.0, RC car, 2.4GHz RTR

The Night Racer 2.0 brings low-slung on-road styling and ready-to-run RC action into one focused 1:10 setup, with a 2.4 GHz control system and a top speed of 20 km/h shaping fast laps on smooth ground. At 485 mm long, 200 mm wide and 125 mm high, the body cuts a sharp racing silhouette that stands out in motion and under evening light. A 260 mm wheelbase and a weight of 737 g give the chassis a balanced footprint for quick steering inputs and stable tracking through linked corners. The differential transmission helps the driven axle work cleanly when the car changes direction, while the suspension layout keeps the wheels in contact over uneven patches and transitions. The included 7.4 V 1200 mAh Li-Ion drive battery supports up to 40 minutes of driving time, and the USB charger keeps the running gear simple to prepare between sessions. Detailed paintwork adds a finished motorsport look, and the blue illuminated rim design sharpens the visual effect once the light drops. On a driveway, in a car park or across a smooth indoor surface, the RTR setup gets the car moving with the supplied remote control system and included transmitter batteries. The compact racing profile, quick response and illuminated wheel styling suit short speed runs, repeated corner practice and evening cruising alike.

RC cars

1:12 RaceRival Combo, RC car, 2.4G RTR

€59.99

The 1:12 RaceRival Combo brings 2 fully assembled RC cars into one set, creating instant side-by-side racing with matching 2.4 GHz radio control. Each model measures 304 mm in length and uses a 3.7 V Li-Ion drive battery with 500 mAh capacity, giving the pair a compact racing format with rechargeable power for repeated sessions. The set includes 2 remote controls, 2 Li-Ion drive batteries, 2 USB chargers and 4 AA transmitter batteries, so both vehicles are equipped for running from the start. A maximum driving time of 40 minutes keeps races going beyond a quick sprint and leaves room for repeated heats, overtaking attempts and back-to-back comparisons between the 2 cars. The pistol-grip transmitters use a trigger for throttle input and a side steering wheel layout familiar from hobby-grade RC driving. Steering fine adjustment on the vehicles helps correct the running direction when the track or surface calls for a more precise setup. Front LED lighting remains clearly visible as the cars move through indoor floors or paved outdoor sections, while the printed body shells give each model its own strong race-day presence. With an age marking of 8 years and up, the set suits shared racing sessions at home, quick duel formats in the driveway and casual practice laps where both cars can be charged, lined up and sent off again.

RC lorries & RC trucks

1:14 3-axle Material trailer, RC trailer

€699.99

At 1:14 scale, this 3-axle Material trailer brings the look and handling of a working cargo hauler into a detailed RC setup. The 981 mm long body combines a laser-cut steel frame in 3 mm and 1 mm sections with a real wooden floor application, creating a technical build with strong visual contrast between metal structure and load bed. The front wall is made from aluminium, while the rear bumper uses 8 mm aluminium for a solid, sharply defined finish. Left and right steel underride protection adds another authentic construction detail to the lower sides. The CNC-milled aluminium dropsides carry engraved surfaces and are built for active use rather than fixed display, with 9 functional panels, removable dropside posts, and 4 hinges on each dropside made from 1 mm steel. Neodymium magnets handle the locking, giving the side sections a tidy closing action without bulky external catches. Wide chromated wheels with ball bearings and wide tyres support smooth trailer movement, and the included suspension offers an optional 8 mm elevation for a different ride height. A steel spare wheel holder with spare wheel is fitted, and the finished trailer measures 981 x 195 x 210 mm with a weight of 6,900 g. Age 14+

Models & trailers

1:14 Goldhofer BAU STN-L3, low loader kit

€584.99

Heavy-haul transport has a distinct presence in scale form, and the Goldhofer BAU STN-L3 brings that character into a 1:14 low loader kit with a long 1000 mm body, a width of about 200 mm, and a height of 270 mm. The laser-cut, hard-soldered steel profile construction gives the trailer its technical look, while the plateau with tailgate extends the transport layout for detailed truck scenes. The build centres on mechanical functions that suit model-building enthusiasts. The split folding loading ramps are arranged in 3/4 and 1/2 sections and can be folded down by hand for driving operation. A ramp length of 290 mm in the raised configuration is stated in the data. Three rear axles carry twin tyres, and the axle area is detailed with dummy air springs for a scale heavy-duty appearance. Ball bearing mounting supports the running gear, and the 7-chamber taillights can be retrofitted electrically. All columns are mechanically adjustable, and the front support area can be expanded with optional E-support legs. The trailer fits all Tamiya trucks, making it a strong match for detailed tractor units in 1:14 truck layouts. On a workshop bench, in a transport diorama, or coupled for slow manoeuvres with scale cargo, the low deck, upright ramp geometry, and multi-axle layout create the look of a working heavy equipment hauler. Age 14 Years  Warning! Not suitable for children under 14 years.

RC tractors

1:16 Deutz-Traktor 8280TTV, RC tractor

€109.99

The Deutz-Traktor 8280TTV in 1:16 scale brings agricultural RC driving into a compact format with a matching trailer and a fully equipped ready-to-run setup. The model uses a 2.4 GHz remote control system and arrives with the drive battery, USB charger and 2 x LR03 AAA transmitter batteries, so all core components for operation are already in the box. Its 7.4 V system pairs with a 500 mAh Li-Ion battery to deliver up to 90 minutes of operating time, giving the tractor enough endurance for repeated hauling runs, careful reversing and steady trailer work. The trailer adds a second handling element to each session, since turns, alignment and positioning need more control than a single vehicle on its own. With 5 frequency channels available, the radio setup supports controlled input during forward runs, direction changes and tighter manoeuvres. The ready-to-run format keeps the focus on driving rather than sourcing the basic operating equipment separately. On the floor, the tractor and trailer combination suits routes with bends, loading-play setups and repeated parking tasks where the longer overall shape changes how each turn is approached. The 8+ age marking fits a model that combines vehicle control, trailer guidance and battery-powered runtime in one clearly structured RC format.

RC cars

1:24 Ford GT, RC car, 2.4 GHz RTR

€24.99

The Ford GT became one of the defining super sports car shapes of its era, and this 1:24 RC car brings that low, wide silhouette into a compact format built for quick laps and precise control. With a fully assembled ready-to-run setup, the model goes straight from charging to driving with the included 2.4 GHz remote control, Li-Ion drive battery, USB charger and transmitter batteries. At 195 mm long, 80 mm wide and 49 mm high, the body keeps the proportions of the road car clear while staying easy to handle on smaller indoor routes. The 172 g weight gives the chassis a light, agile feel in motion, and the fine-tuned steering supports accurate line changes through short straights and tighter bends. Front and rear LED lighting extends the visual effect beyond daylight conditions, while the licensed Ford design and realistic sports car look keep the model closely tied to its full-size inspiration. The 3.7 V drive system uses a 500 mAh Li-Ion battery and reaches up to 60 minutes of driving time at full capacity, making longer sessions possible without frequent charging breaks. Non-slip rubber tires work with the rear differential to maintain traction and stable handling as the car accelerates, turns and settles into repeated circuit runs. Age 6+ marks the recommended age, and the complete RTR format suits first RC laps as well as relaxed driving sessions for motorsport fans.

RC buggys

1:8 Rock Wilder, RC car, 100% RTR

€174.99

The 1:8 Rock Wilder brings large-scale off-road presence to every run with a 530 mm long chassis, full suspension and digital proportional control. In black and red trim, the ready-to-run setup pairs a type 550 brushed motor with water-resistant RC components for driving on mixed terrain where dust, loose gravel and uneven ground are part of the appeal. Its 355 mm width and 220 mm height give the model a broad, stable stance, while the 2552 g weight adds substance as the suspension works through ruts and bumps. Reinforced suspension arms support the independent layout at each corner, and the quick-change battery mount keeps battery swaps straightforward between sessions. The included 7.4 V 3000 mAh Li-Ion drive battery, USB charger, 2.4 GHz remote control and 4× LR06 transmitter batteries cover the core running equipment in one box. Age recommendation: 14 years+ The Rock Wilder suits trackside bashing, open gravel areas and compact dirt routes where the proportional steering and throttle inputs can be used with precision. Water-resistant electronics help the model stay focused on the route when conditions turn messy, and the RTR format keeps the emphasis on charging up and heading out for the next run.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 MB 1620 flatbed truck, RC model, RTR

€129.99

The 1:87 MB 1620 flatbed truck with trailer brings compact RC control into H0 railway scenes with a fully assembled 100% RTR setup and finely scaled proportions. At 187 mm in length, the model is sized for dioramas and model railroad layouts where precise movement, lighting and sound add life to streets, depots and loading areas. A 2.4 GHz remote control system handles steering, speed and the switchable engine sound, while the integrated 3.7 V 75 mAh Li-Ion drive battery recharges through the transmitter in about 45 minutes. Front and rear LED lighting supports realistic operation in dimmer layout settings, and the very small turning circle helps the truck work through narrow routes and confined manoeuvring zones. The detailed body uses high-quality plastic construction with fine printing, and the removable tarpaulin changes the look of the trailer for different scene setups. A driver figure adds another scale detail for display, and the included trailer extends the vehicle's presence in transport scenes. With up to 60 minutes of operating time, the model suits longer running sessions on H0 layouts, from careful reversing at a loading bay to steady road movement between buildings and trackside structures.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 Mercedes Benz 200/8 Taxi, RC car, RTR

€109.99

The Mercedes Benz 200/8 shaped the look of everyday saloons in the late 1960s and 1970s, and this 1:87 RC car brings that familiar taxi silhouette into a compact radio-controlled format. The small scale and RTR layout combine classic road-car character with immediate driving action on desks, display areas, or smooth indoor surfaces. Its 100% RTR specification means the key running setup is already part of the set, keeping the focus on steering inputs and controlled movement rather than sourcing core equipment first. The included 5 batteries support a ready-to-start configuration straight from the pack. With a recommended age of 14 years, the handling and scale suit enthusiasts who enjoy compact vehicle models with a recognisable real-world subject. The taxi styling gives the body a distinct period look that stands apart from modern racing or off-road themes. Between short driving sessions, the 1:87 format also makes the model easy to place in a collection of miniature road vehicles. It works well as a small RC model for indoor runs, as a conversation piece on a shelf, or as a classic Mercedes Benz subject in a compact hobby lineup.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 Mercedes Benz 200/8, RC car, 100% RTR

€109.99

The Mercedes-Benz /8 series shaped everyday motoring in the late 1960s and 1970s, and this 1:87 Carson model captures that familiar saloon silhouette in a compact radio-controlled format. Finished in blue and supplied as a 100% RTR version, the miniature is set up for immediate use with 5 batteries included. Its 1:87 scale gives the model a notably small footprint, making controlled runs possible in spaces where larger RC cars would feel oversized. The classic 200/8 body shape brings a recognisable road-car character to each manoeuvre, while the compact format invites careful steering, short direction changes and neat placement on smooth indoor surfaces. With batteries already part of the set, the focus stays on the driving session itself rather than on sourcing the basic power supply first. Between runs, the blue finish and saloon proportions also make the model easy to place on a desk or shelf as part of a collection of compact vehicles. The combination of RTR convenience, included batteries and 1:87 scale makes this Mercedes Benz 200/8 a concise entry into small-format RC driving for hobbyists aged 14 years and up.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 VW Beetle, RC car, 2.4 GHz RTR

€104.99

The Volkswagen Beetle remains one of the most recognisable car shapes of the 20th century, and this 1:87 RC version translates that silhouette into a compact model built for active driving. At 50 mm long, 20 mm wide and 18 mm high, the Bahama blue Beetle combines miniature scale with fully controllable handling and a detailed body that carries the character of the original into H0 format. Its 2WD RWD layout works with a brushed motor to deliver balanced running behaviour, while the 10 g weight keeps the model light on the surface. The officially licensed Volkswagen design is matched with front and rear LEDs that define the car clearly as it moves through table layouts, floor circuits or display-style street scenes. The 100% RTR set includes a permanently installed 3.7 V 40 mAh Li-Ion battery, 4x AAA transmitter batteries and a storage case, so the driving setup is complete straight away. The 2-channel radio system supports controlled runs with a range of up to 50 m, making the Beetle suitable for compact slalom routes, desk-side driving and small indoor courses where accurate line changes matter. Age marking: 14 years. Charging takes place through the transmitter and keeps the model ready for regular sessions between laps.

RC models in 1:87 scale

1:87 VW T1 Bus Van, RC car, car trailer

€114.99

The VW T1 became one of the most recognisable light commercial vehicles of the 1950s, and this 1:87 RC version brings that silhouette into a compact driving format with a matching car trailer. At 115 mm long, 28 mm wide and 21 mm high, the ready-to-run model fits neatly into small layouts while still carrying the bus profile, printed finish and illuminated front and rear lighting. The 2.4 GHz radio system gives stable control for 1-player operation, and the fully proportional setup allows measured inputs instead of simple on-off movement. With a weight of 18 g, the model stays light in hand and easy to place on shelves or in model scenes between runs. The included Li-Ion drive battery is rated at 3.7 V and 75 mAh, while 4 LR03 AAA transmitter batteries are also included in the set. Steering trim supports precise correction when the bus tracks slightly left or right, which is especially useful on narrow routes where the small turning circle can be used to full effect. The display case adds a clean way to store the bus and trailer between sessions or present them as part of a collection. On a desk, shelf layout or compact indoor course, the combination of trailer detail, proportional control and long 50-minute runtime creates a focused micro RC driving session with a strong model-railway scale presence.  Warning! Not suitable for children under 14 years.

RC models in 1:87 scale

1:87 VW T1 Kastenwagen Jägermeister, RC car

€104.99

The VW T1 became one of the defining light commercial vehicles of the post-war era, and this 1:87 Carson version translates that familiar panel van shape into a compact RC format with Jägermeister livery. At 50 mm long and 20 mm wide, the model brings authentic proportions, detailed printing and front and rear LED lighting to desks, shelves and small indoor driving spaces. Its fully proportional control system gives measured steering and speed response instead of simple on-off inputs. A steering trim function helps fine-tune straight running, while the very small turning radius suits narrow table courses and close obstacles. The 2.4 GHz radio system supports stable control, and the sensitive forward and reverse function makes low-speed corrections easier in confined spaces. A brushed motor and 2WD RWD layout shape the driving character, while the permanently installed 3.7 Volt 75 mAh Li-Ion battery supports up to 50 minutes of travel time. With a height of 19 mm and a weight of 16 g, the van stays easy to place and store between runs. The set includes a display case for storage, which also keeps the miniature body protected when the model is off the course. 4x AAA transmitter batteries are included, so the RTR format covers the essentials for immediate indoor driving.

RC helicopters

Cyber Copter IR 2Ch, RC helicopter, RTF

€21.99

The Cyber Copter IR 2Ch brings compact helicopter flying into a ready-to-fly format with a modern grey fuselage and a focused control layout. At 230 mm long, 95 mm high and with a 190 mm rotor diameter, this RC helicopter stays compact enough for indoor sessions while reaching speeds of up to 10 km/h. Its flight system combines infrared control with 2 channels for clear directional input, and the integrated gyroscope helps keep movement steady once airborne. Fine tuning comes from individually adjustable left and right trim, allowing the flight path to be corrected to suit the room and the handling style. The switchable LED position lights are activated from the transmitter, making the model easier to track visually when the light drops at dusk. A 3.7 V 150 mAh LiPo flight battery powers up to 8 minutes of runtime per charge, and the USB charger keeps charging straightforward between flights. The set includes the ready-to-fly model, remote control, USB charger and 3 AAA transmitter batteries, so the first takeoff can follow soon after charging. Age 8 Years

RC yachts

Nano Racer Yacht 2.4G

€19.99

RC action on the water! With the Nano Racer Yacht, luxury RC fun on the water is realized. The ready-to-run yacht model delivers full driving fun right after unpacking and brief charging. It is controlled with a 2.4 GHz radio remote control and offers a range of up to 40 meters. Thanks to the safety shutdown, the propellers only work when the model is in contact with water. All RC components are water-resistant, making the yacht ideal for exciting action on the water. The set includes a LiPo battery and clear instructions for quick start-up. Compact, fast, and easy to control, the Nano Racer Yacht is a fun watercraft for hobby and play.

RC helicopters

Nano Tyrann 230 Gyro, RC helicopter, 2CH IR

€24.99

Compact dimensions and a coaxial rotor layout give the Nano Tyrann 230 Gyro a light, agile presence in indoor flight, while intelligent gyro electronics keep the model composed during lift-off, hovering and direction changes. At 225 mm long, 97 mm high and only 31 g in weight, this 2-channel RC helicopter brings controlled handling into a format that is easy to store and quick to prepare. The infrared control system focuses the flying experience on the core inputs, with left and right trim on the transmitter to correct the track when needed. A 3.7 V 130 mAh LiPo flight battery powers up to 8 minutes of flying time, and charging runs through the included USB cable. The rotor diameter of 180 mm gives the helicopter a balanced footprint for indoor rooms, where short climbs, hovering practice and careful turns can be repeated in a manageable space. The switchable LED adds a visible point at the nose during flight and can be controlled directly from the transmitter. The ready-to-fly set suits spontaneous sessions in living rooms, hobby spaces or other indoor areas where compact RC aircraft can be flown with precision. Age 12 years and up. Only suitable for indoor use.

RC quadcopters

X4 Quadcopter Yairo, RC aircraft, 2.4 GHz RTF

The X4 Quadcopter Yairo brings compact quadcopter flying together with illuminated detail and straightforward control in a ready-to-fly format. With a ring diameter of 150 mm, a height of 37 mm and a weight of 52 g, the model stays light and agile in the air while the three-colour LED setup gives each flight a vivid visual presence. Its electronically rotatable LED ring is controlled by the remote control, adding a moving light element that changes the look of the quadcopter during flight. The 3.7 V 500 mAh LiPo flight battery supplies up to 8 minutes of runtime, and the included USB charger keeps the setup simple between sessions. 4 frequency channels support responsive handling, while the compact dimensions make the model easy to carry to open indoor spaces or calm outdoor areas. The included LR06/AAA transmitter batteries mean the full set is ready for use straight from the contents provided. Short practice flights, evening hovering sessions and quick manoeuvre runs all suit this RC aircraft well. The 8+ age marking and 1-player format make it a focused flying model for learning control inputs, refining reactions and enjoying illuminated flights with a compact quadcopter layout.

RC speed boats

XS Deep Sea Dragon, RC submarine, 100%RTR

€39.99

Compact RC submarines bring a different kind of model action, and the XS Deep Sea Dragon shifts that action below the surface. This 100%RTR RC submarine combines a compact orange hull, 3-channel 40 MHz control and blue LED illumination for visible manoeuvres in baths, pools and aquaria. The set includes the mini submarine with RC system, a 3.7 V 90 mAh Li-Ion drive battery, a USB charger, 2 transmitter batteries and instructions. Forward, backward, left and right steering are joined by dive and surface functions, so movement is not limited to a flat path across the water. The blue LEDs stay visible during operation and help keep the model in view while it changes depth. With up to 6 minutes of runtime, each charge suits short underwater runs with a clear start and finish. The USB charging cable can be stowed in the transmitter, so the charging lead stays with the control set between sessions. In use, the compact format suits smaller water spaces where tight turns and depth changes stay easy to follow. Age 8+ marks the recommended age. The submarine is intended for fresh water use in swimming pools, baths and aquaria; do not use in salt water.

RC tires & rims

1:10 2WD Wheel Set XL, RC tire set

€37.99

Give your 2WD RC buggy or truck a massive performance upgrade with the Carson 1:10 XL Wheel Set. This specially designed set is the ideal solution for model builders who want to give their vehicle an impressive “monster” look and improved off-road capability. What makes this set special is its precise tuning: Since XL tires can affect conventional steering angles, Carson includes the matching steering levers right in the package. These are engineered exactly to perfectly compensate for the larger wheel diameter of 105 mm and ensure full maneuverability. The technical details are specifically designed for the Tamiya DT-02 and DT-03 chassis —while the front rims are designed to directly accommodate ball bearings, the rear rims use the proven 12mm hex drive, which is standard on Tamiya and many other brands. The black-and-white color scheme also provides a modern, sporty look. Whether on loose gravel or rough terrain, the wide 65-mm contact patch guarantees optimal traction and stable handling.

RC tires & rims

1:10 All-Terrain Wheel Set, RC tyres, 2WD

€31.49

Built for 1:10 2WD buggies and trucks, this 4-piece all-terrain wheel set brings a track-ready combination of steering precision and drive traction to mixed surfaces. The black and white wheel design pairs 2 front tyres and 2 rear tyres in different widths, creating a layout that suits the demands of a 2-wheel-drive setup on road, gravel, sand and grass. At the front, the 26 mm tyre width supports a more exact steering response, while the 43 mm rear tyres give the driven axle a broader footprint for stronger acceleration grip on loose ground. Each wheel has a 90 mm diameter, giving the chassis a useful balance of agility and clearance over uneven terrain. Foam inserts inside the tyres help the contact patch stay consistent as the model changes direction or loads up under power. The front rims are designed for ball bearings, and the rear rims use Tamiya hex mounts, matching the different mounting needs across the vehicle. Because the tyres are professionally pre-glued, the set goes straight into the workshop plan without a separate bonding step. That makes it a practical choice for replacing worn running gear, preparing a buggy for mixed-surface driving, or setting up a truck for more dependable traction away from smooth tarmac.

RC tires & rims

1:10 All-Terrain Wheel Set, RC tyres, 2WD/4WD

€31.49

Built for mixed-surface running, this 1:10 all-terrain wheel set combines a 90 mm diameter with a 2WD/4WD layout that suits a wide range of RC setups. The 4-piece configuration uses 2 front tyres and 2 rear tyres, creating a purposeful combination for models that need clear steering response at the front and stronger drive support at the rear when the surface changes from asphalt to loose ground. The front tyres measure 26 mm in width, while the rear tyres measure 43 mm, giving the set a staggered format that supports balanced handling under acceleration. Black and white rims add a clear competition-inspired look, and the tyres are professionally pre-glued to the rims for a clean fit straight from the pack. Integrated foam inserts help the tyres hold their shape during intensive driving manoeuvres, so the tread can work consistently as the model loads up in turns and over uneven sections. The wheel set is designed for 4 x 12 mm Tamiya hex mounts, making it a practical replacement set or a fresh running option for compatible chassis. On road, gravel, sand or grass, the all-round tread is aimed at drivers who switch between surfaces instead of tuning for only one. The set suits routine replacement after wear, but also works as a handling-focused update when a model needs broader traction coverage for everyday RC running.

RC combustion engines & glow plugs

1:10 BL Motor Dragster Turbo 2.0, motor

€34.99

The 1:10 BL Motor Dragster Turbo 2.0 3200KV is a brushless drive unit created for electric RC vehicle projects with a clear focus on dragster-style power delivery. Its 3200KV specification points to a fast-revving motor character that suits straight-line acceleration setups and gives model-building enthusiasts a concrete tuning component for 1:10 platforms. As a standalone motor, this unit fits into workshop-based RC builds where the drive system is chosen part by part. The brushless layout makes it a relevant option for hobbyists comparing replacement motors or planning a fresh electric configuration around a defined KV value. The Turbo 2.0 naming gives the motor a distinct place within the range, while the 1:10 scale reference keeps the application tied to model car use rather than full-size electronics. No batteries are included. The age marking is 14 Years. On the bench, this motor suits rebuilds, performance-focused maintenance and targeted drivetrain changes in electric model cars. It also works well as a search-friendly option for enthusiasts narrowing a setup by scale, motor type and 3200KV specification before matching the rest of the electronics separately.  Warning! Not suitable for children under 14 years.

RC brushless motors

1:10 Dragster Turbo 2.0, brushless set

€59.99

The 1:10 Dragster Turbo 2.0 brushless set brings a compact power package to RC vehicle builds with a sensorless 3200 kV motor and an electronic speed controller matched to hobby-grade running. In the chassis, the black finned motor layout and separate controller create a clean drive setup for fast acceleration and direct throttle response. The motor delivers a no-load speed of 24,420 RPM and approx. 390 W short-term output, with 53 A continuous current for sustained running. Its dimensions of 35.8 x 50 mm and a shaft diameter of 3.175 mm provide concrete fitting data for compatible installations, while the motor weight of 148 g and ESC weight of 80 g help when planning the balance of a 1:10 model. The controller is designed for 7.4 V operation and works with 2S LiPo or 6-cell NiMH battery packs. Forward, brake and reverse functions are built into the ESC, and the T-Plug connector forms part of the power connection. This set suits RC car projects that need a coordinated motor and controller combination rather than separate component sourcing. Included are the Dragster Turbo 60 A speed controller, the brushless motor and instructions.  Warning! Not suitable for children under 14 years.

RC electric motors & controllers

1:10 Dragster Turbo 2.0, brushless set

€59.99

The 1:10 Dragster Turbo 2.0 brushless set brings a matched drive upgrade to electric RC models with a 2000 kV sensorless motor and a 60 A electronic speed controller. This 2-part combination is built for hobby setups that need clear throttle delivery, compact installation and a defined power package in one box. The motor measures 35.8 x 50 mm, uses a 3.175 mm shaft and weighs 148 g, making it a concrete fit option for many 1:10 chassis layouts where motor space and shaft size matter during planning. Its no-load speed reaches 15,170 RPM, while short-term output is rated at approx. 236 W for lively response when the drivetrain comes under load. The ESC adds 80 g, handles 60 A continuously and up to 360 A peak, and manages forward, brake and reverse functions through a sensorless brushless system. Power supply compatibility covers 2S LiPo and 6-cell NiMH packs, with a T-Plug connector already specified. This set suits rebuilds, replacement projects and performance-focused electronics swaps in 1:10 electric vehicles. Included are the Dragster Turbo 60 A speed controller, the brushless motor and instructions, giving model-building enthusiasts a clearly defined basis for a fresh drive configuration.  Warning! Not suitable for children under 14 years.

RC electric motors & controllers

1:10 Dragster Turbo 2.0, motor, 2600KV

€34.99

The 1:10 BL Motor Dragster Turbo 2.0 2600KV is a brushless drive component for electric model vehicle setups, centered on a 2600KV motor specification and a format matched to 1:10 applications. As a dedicated replacement or upgrade part, it brings the drive system back into service with a clearly defined motor unit for workshop benches, rebuilds and running repairs. Within a powered vehicle setup, the motor sits at the heart of the drivetrain, making the KV rating a key reference point when matching the unit to the existing electronics and the intended running character. The product data identifies this version specifically as the Dragster Turbo 2.0 motor, which keeps the designation clear when replacing a worn unit or sourcing the correct spare for an existing model. Because this is a component rather than a complete vehicle, the focus stays on fit within an electric model system and on the practical value of having the correct motor type ready for maintenance. The 14 Years age marking is stated in the product data. On the workbench, this kind of motor suits planned repairs, drive refreshes and parts-led tuning sessions where a named 1:10 brushless unit is the required starting point for getting a model back on track.  Warning! Not suitable for children under 14 years.

RC truggies & RC monster trucks

1:10 Torque Beast, RC car, 2.4 GHz RTR

€129.99

The 1:10 Torque Beast brings classic monster truck presence to RC driving with a 430 mm length, 310 mm width and 200 mm height that give the chassis a broad, purposeful footprint on rough ground. A solid bumper with integrated LED lighting adds a bright front-end detail, while water-resistant RC components and splash-proof electronics support running when the surface turns damp or dusty. At 1364 g, the model combines its size with a manageable overall weight that suits quick direction changes and repeated runs. The 7.4 V 1500 mAh Li-Ion drive battery is included, and the stated running time reaches 25 minutes before the pack heads back to the USB charger. The fully assembled RTR format keeps the focus on driving rather than setup, and the 2.4 GHz system supports stable control without the frequency crystals older RC systems required. Minimum age: 14 years. On gravel paths, compact dirt sections or uneven yard surfaces, the Torque Beast has the ground clearance and tire format to keep the run lively without losing control. Evening sessions gain extra character from the front LED lighting, and the included battery set means the truck is equipped for the first outing straight away.

RC tires & rims

1:10 Wheel Set XL, RC wheels, 4WD 12 mm hex

€34.49

Large-diameter wheels can change both the look and the handling of an RC build, and this 1:10 4WD wheel set XL does exactly that with 4 complete wheels in black and white. The 105 mm diameter and 65 mm width create a noticeably larger footprint that suits rougher ground and gives the chassis a more assertive visual presence. Inside each tyre, foam inserts are matched to the construction so the rubber is supported under load instead of folding over or rolling at speed. That internal support helps the tread stay more stable through acceleration, direction changes and uneven sections, which can make the model feel calmer and more predictable in motion. The set is built around 12 mm hex mounting, a widely used format that allows straightforward installation on matching wheel hubs. Compatibility is stated for Tamiya hex mounts, making the set a practical option for many established 1:10 4WD platforms. On loose surfaces such as sand or grass, the XL dimensions can help the model carry momentum with a broader contact area. On firmer ground, the same wheel size gives the chassis a fuller, more aggressive stance that changes the overall character of the build without altering the core layout.

RC Crawler

1:10 X-Crawlee Pro 3.0, RC crawler, 100% RTR

€249.99

The 1:10 X-Crawlee Pro 3.0 brings crawler driving into a 43.5 cm format built for rough ground, with a 270 mm width, 235 mm height and a weight of 2280 g that gives the model a planted stance on the trail. Its 100% RTR setup puts the focus on driving from the first session, while the 2.4 GHz remote control system keeps control inputs clear and direct. Power comes from the included 7.2 V NiMH drive battery with 1800 mAh, charged via the included 7.2 V / 1 A USB charger. At full capacity, driving time reaches up to 70 minutes, giving longer runs across stones, dirt tracks and uneven paths without frequent charging breaks. The controller is compatible with NiMH and LiPo batteries, which broadens battery choice for later setup changes. Full ball bearings support efficient running through the drivetrain, while the suspended rigid axles give the crawler the axle movement needed for slow, technical sections. The ready-to-run set includes the model, the radio system, the drive battery, the USB charger, 4 AA transmitter batteries and the manual. With a 14 years+ age marking and a single-vehicle setup, the X-Crawlee Pro 3.0 suits focused crawling sessions where line choice, throttle control and steering precision shape every climb.  Warning! Not suitable for children under 14 years.

RC truggies & RC monster trucks

1:10 XS Tekuro, RC car, 4WD 100% RTR

€199.99

The 1:10 XS Tekuro brings fast off-road driving into a 410 x 300 x 175 mm format with permanent 4WD, a high-torque 550 brushed motor and a top speed of up to 40 km/h. Grey and green bodywork, 110 mm monster tyres and a raised stance give the model a strong trail-ready presence before the first run even starts. Its drivetrain is built around a central steel cardan shaft, reinforced steel drive shafts at the front and rear, and metal differentials with steel bevel gears on both axles. Ball-bearing mounting throughout supports efficient running, while the XT60 high-voltage plug system and quick-change battery holder simplify battery swaps between sessions. The 8 kg steering servo uses a metal gearbox and water-protected construction, matched with splash-protected electronics and a water-protected 2.4 GHz radio system. The included 2600 mAh 7.4 V Li-Ion battery supports about 15 minutes of driving time, and the complete RTR setup keeps preparation focused on charging and heading out. At 1741 g, the chassis has the planted feel needed for dirt paths, gravel sections and uneven ground. Tight turns, short bursts of acceleration and repeated launch attempts all suit the Tekuro's mix of traction, suspension travel and wheelie-ready rear setup.  Warning! Not suitable for children under 14 years.

Basic accessories

1:14 2-Axle Boxed Trailer, model kit

€589.99

A 2-axle box trailer is a familiar sight in road freight, built to carry cargo in a closed body while keeping the load protected on the move. This 1:14 model kit brings that transport format into a detailed build with a laser-cut steel frame, a box body with CNC-milled aluminum parts, and the long, clean proportions of an enclosed trailer behind a tractor unit. The chassis uses 3 mm and 1 mm steel, while the bogie is formed from sheet steel in a sandwich structure. Wide chromated wheels run on ball bearings and carry wide tyres, and steel underride protection sits on the left and right sides. At the rear, an 8 mm aluminum bumper adds another machined metal detail, and a 1:14 trailer splash guard completes the lower section. The body measures 545 mm in length, 195 mm in width, and 290 mm in height, with a total weight of 4,800 g. Assembly is required, with a stated assembly time of 600 minutes. In use, the rear loading door opens on aluminum hinges through 270°, and magnets handle the door locking. Coupled behind a suitable 1:14 tractor unit, the enclosed body suits scale logistics scenes, articulated truck displays, and workshop builds that focus on metal construction, moving parts, and realistic trailer proportions. The kit includes instructions.

Models & trailers

1:14 2-Axle Dump Semi-Trailer, trailer

€589.99

Built in 1:14 scale, this 2-axle dump semi-trailer brings the look of a full-size tipper into a model-building format with a rigid PVC body, a CNC-milled aluminum frame and a 4-wheel layout. The silver dump body, black chassis and raised front platform create the working profile of a road-going bulk trailer, whether coupled to a tractor unit or parked on its support legs. The assembly kit focuses on mechanical detail rather than simplified styling. Vertical body panel lines, mudguards, rear underrun protection and ladder elements give the trailer a technical finish, while the king pin can be adjusted to suit the setup. The chassis uses new axles with 8 mm lift, and the rear section is shaped around a mechanically unlocking tailgate for realistic unloading action when a tipping function is installed separately. 7-chamber taillights and dummy air spring details extend the scale appearance across the rear and underside, and the ball-bearing wheel setup supports smooth movement during handling. On a workshop shelf, in a truck yard scene or behind a matching 1:14 tractor, the semi-trailer adds a strong construction-transport theme with visible engineering throughout the frame and body. Assembly kit and manual are included. A spindle drive, motor, battery, switch, radio gear, a charger and paints are required separately for expanded functions and finishing.  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 2-Axle Dump Trailer, trailer kit

€519.99

The 1:14 2-Axle Dump Trailer brings working tipper style into a scale truck setup with a tandem-axle layout, a gray rigid PVC dump body and a steel profile frame with laser-cut, laser-welded construction. Built as an assembly kit, it focuses on the mechanical character of a real dump trailer, from the drawbar and support leg to the rear gate area and underbody linkage. The chassis uses 8 ball bearings across the wheel setup, giving the running gear a more precise feel as the trailer rolls behind a compatible tractor unit. Fulda Variotonn wide offroad tyres and the trailer axle with air ride dummy push the model further toward commercial-vehicle realism, while the 7-section tail lights add a recognisable rear-end detail. The automatic back wall locking with 2-hook design gives the rear section a functional finish that matches the tipper concept. The support leg keeps the trailer upright when detached, and the drawbar with hitch eyelet completes the classic central-axle trailer layout seen in heavy haulage scenes. On the bench, the kit offers a focused build around frame, axle and body assembly. Once finished, the trailer suits construction, transport and unloading scenes in 1:14 scale layouts, whether parked as a standalone model or coupled into a larger truck combination. Age 14 Years. Spindle drive, gear box motor, a control switch and paints are required separately.  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 2-Axle Material Trailer, trailer kit

€574.99

Built for 1:14 truck scenes, the 2-Axle Material Trailer brings a long loading bed, twin-axle layout and working drop-side bodywork into a scale transport build with a clear commercial look. The grey panel sides, dark front bulkhead and wood-look floor give the trailer the character of a real material hauler, whether it is coupled behind a road tractor or parked at a loading point. The kit structure goes beyond a simple rolling chassis. The assembly sequence includes 2 axle units, a pivoted bogie, a main frame with crossmembers, mudguards, underride protection, rear bumper parts and upright posts around the bed. Ball bearings are fitted into each wheel hub, and the axle geometry offers normal height or a +8 mm position during assembly. Rear light housings are part of the build, and the manual also shows optional LED taillight boards as separate accessories. A spare wheel holder and additional fittings are listed as optional accessories rather than included contents. Once assembled, the trailer suits realistic loading and transport layouts in 1:14 scale, from building-material scenes to depot and yard setups. The opening side panels and rear section support a more active display style, while the detailed underframe, mudflaps and side protection parts give the finished trailer convincing presence from low viewing angles.  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 2-axle Riedler, stanchion trailer

€509.99

The 1:14 2-axle Riedler stanchion trailer brings timber-haul detail into a scale transport setup with a steel sandwich frame, solid aluminium stanchions and a long, purposeful silhouette. At 620 x 190 x 305 mm and 2,600 g, the trailer adds real presence to a model road train while reflecting the look of the full-size Riedler vehicle named in the licence. Its mainframe uses 3 mm and 1 mm sheet steel parts that are laser cut and CNC bent, and the bogie follows the same sandwich construction for a consistent mechanical layout. The mounted bogie is adjustable and uses sliding pads to support manoeuvring through tighter course sections. A one-piece drawbar in fibre-reinforced plastic carries a chequer plate application and is held at a coupling height of 75 mm by 2 springs. The semitrailer axle includes dummy pneumatic springs, while the left and right underride guards and the CNC-milled rear bumper add further metal detail. The stanchion holders can be loosened with 2 grub screws, then repositioned or removed to suit different loading arrangements for logs or other long cargo. Ball-bearing mounted chromium wheels with wide tyres, mudguard splash protection, bumper mud flaps, a licence plate holder and 7-compartment rear lights build up the finished transport character. A decoration set is included. Age 14 Years. The Carson towing coupling 500907182 is required separately for use on the TAMIYA Volvo FH16 tractor unit.  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 20Ft. Sea-Container, kit, trailer load

€199.99

Freight containers shaped modern transport with a standardised form built for road, rail and port handling. This 1:14 20Ft. Sea-Container Kit brings that familiar cargo silhouette into a scale truck setup with a 432 mm length, 180 mm width and 185 mm height. The structure combines an anodised silver aluminium frame with plastic sheet body sections that reproduce the look of a traditional container. Corrugated surfaces, corner details and the separate frame layout give the model the character of a working freight load rather than a plain box shape. The plastic panels are paintable, which supports custom liveries, fleet styling or a weathered finish that matches a chosen tractor unit and trailer combination. At the rear, the doors are movable and fitted with a locking mechanism, so the handling detail is part of the build rather than only a visual effect. The container is designed for the 2 axle container semi-trailer 500907334 and locks to the chassis via twist-locks. That mounting method reflects the technical logic of full-size container transport and helps the model sit naturally in logistics, harbour or long-haul display scenes. 14 Years marks the recommended age.

Models & trailers

1:14 20Ft. Semitrailer, trailer kit, tandem axle

€274.99

Built around a 1:14 scale layout, the 20Ft. Semitrailer kit brings container transport style into a detailed truck setup with a black anodised aluminium frame and a compact tandem-axle format. The 475 mm long chassis creates a clear, purposeful silhouette behind a tractor unit, while the 180 mm width and 135 mm height keep the proportions aligned with scale road-haulage scenes. The running gear combines swing axle suspension with flat springs, giving the underframe a more technical, model-engineered character than a plain static trailer base. Tyres with foam inserts add substance to the wheel setup and support a fuller tyre shape on the rims. Mechanical seat posts strengthen the parked semitrailer look at the front section and add another visible chassis detail for display or workshop scenes. The open kit format also leaves room for a container-focused build concept rather than fixing the trailer to a single body style from the outset. Coupled to a matching truck, the semitrailer suits freight yard layouts, road transport displays and scale driving sessions built around container handling themes. A suitable lamp set, 300056502, is available for builders who want to extend the trailer with matching light equipment. Age 14 Years

Models & trailers

1:14 3-Axle Flatbed Trailer III, trailer

€539.99

Heavy transport takes shape in 1:14 scale with the 3-Axle Flatbed Trailer III, a detailed kit built to pair with TAMIYA tractors. The long platform, solid front wall and multi-axle layout give the model the look of a working road trailer ready for oversized loads, machinery or palletised cargo. The chassis uses a laser-cut steel frame in 3 mm and 1 mm material, supported by a massive aluminium front wall and steel underride protection on the left and right sides. A bumper made from 8 mm aluminium adds another strong visual and structural element at the rear. The loading area measures 981 mm in length, with an overall width of 195 mm and height of 210 mm, giving the trailer a notably long deck in this scale. At 4,400 g, the assembled model carries a substantial presence on display and in convoy scenes. The new trailer suspension can be built at normal height or with the included +8 mm elevation, adding flexibility to the finished stance. The real wood deck surface and recessed fastening points suit scale freight setups, from construction loads to industrial transport scenes. Ball-bearing wheels support smooth rolling movement, while the spare wheel mounted in its steel holder strengthens the authentic commercial-trailer look. Age 14+ marks the recommended age. The trailer can also be expanded with separately available accessories, including a conversion kit with functional aluminium side walls for building-material transport.

Models & trailers

1:14 3-Axle Fliegl Megarunner, trailer kit

€634.99

Curtain-side trailers shape the look of modern road freight, and the 1:14 3-Axle Fliegl Megarunner brings that transport character into a detailed model-building project. The assembly kit captures the long, low stance of a European semi-trailer with a 995 mm length, a 195 mm height and a red curtain body that stands out clearly beside the white front and rear sections. The build centres on a laser-cut steel frame, steel front wall and 3-axle layout, creating a technical structure with the layered detail that model-building enthusiasts look for in workshop sessions. Along the sides, the curtain body is tensioned with multiple fasteners, while the rear section uses opening doors with a 270° hinge layout for a more authentic trailer finish. Half-round mudguards, a single-arm steel spare wheel carrier and aluminium underride protection add the kind of hardware normally seen underneath full-size transport equipment. The rear bumper carries a laser-cut Fliegl logo, and the wide tyres with chromed rims complete the road-going stance with a bright contrast against the darker chassis parts. On a shelf, in a depot scene or coupled to a 1:14 tractor unit, the trailer adds a strong logistics presence through its triple-axle proportions and curtain-side bodywork. The kit format makes the construction itself part of the appeal, with the manual included for step-by-step assembly.  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 3-Axle Low Loader, trailer, gooseneck

€849.99

Heavy-haul trailers are defined by their proportions, and this 1:14 3-axle low loader captures that look with a long low-bed platform, a stepped gooseneck front section and a rear triple-axle group. The red frame, wood-look centre deck and black running strips create the technical contrast seen on full-size transport equipment, whether the trailer is coupled to a matching tractor unit or shown as a standalone workshop build. The construction goes beyond a simple shell. The manual shows 6 wheel assemblies with ball bearings, a multi-part frame with cross members in 74 mm and 81 mm lengths, and deck sections that lock into place across the chassis. Rear details such as warning boards, mudflaps, lights, hazard markings and LONG VEHICLE graphics build the road-going character of the model. The trailer also supports optional upgrades including a spindle drive gearbox motor, a control switch for the lifting mechanism, LED tail light boards, rectangular lights and an orange flashing beacon. On a finished 1:14 truck combination, the low central bed suits scale transport scenes with construction machines, agricultural vehicles or other oversized loads. The long deck and realistic rear section also make the model a strong centrepiece for shelf display, depot layouts and heavy-transport dioramas. Required separately are a gearbox motor for the lifting device and a control switch for manual lifting.  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 3-Axle Semi-Trailer Ver.III, trailer

€689.99

The 1:14 3-Axle Semi-Trailer Ver.III recreates the long, enclosed form of a box trailer with a white body, red chassis and a detailed 3-axle layout that gives a truck combination a convincing road-going presence. Extended support legs at the front let the trailer stand detached, while the wide rear opening sets up loading scenes with the doors swung fully outward. Details across the chassis and body focus on the hardware that defines a working trailer. The side panels use a screwed sandwich-look construction, and the semi-circular mudguards frame the rear wheel area with a clean commercial-vehicle profile. At the back, an aluminum rear bumper carries 7-section taillights for a technical finish that matches the transport theme. A steel spare wheel holder with spare wheel adds another workshop-style detail to the underframe, and the manually adjustable aluminum trailer support legs underline the functional character of the model. Combined with a compatible 1:14 tractor unit, the trailer suits realistic freight setups, depot scenes and road-train display builds. Open rear doors, visible cargo space and the multi-axle chassis also make it a strong centrepiece for transport layouts focused on loading bays, yard parking and long-haul combinations. Age 14 years+  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 3-Axle Stanchion Trailer, logging trailer

€599.99

Built around a 1:14 scale and a 3-axle layout, this stanchion trailer brings the look of a dedicated timber hauler into a detailed model format. The red chassis, silver stanchions and black fenders create the unmistakable profile of a forestry transport trailer, with the long frame set up to carry elongated loads such as logs or poles in a convincing road-going arrangement. The structure develops through a multi-stage build with 6 wheel assemblies, ball bearings in the wheel hubs and 3 axle units mounted beneath the frame. The suspension uses a new design, and the axle build includes a choice between normal height and a raised +8 mm position. Dummy air suspension details add another layer of scale realism around the running gear. Side underrun guards, a rear bumper, rear light details and a front holder with front plate shape the trailer into a complete heavy-transport subject rather than a simple rolling chassis. On the bench or coupled into a 1:14 truck setup, the trailer suits display scenes centered on forestry, construction or long-load transport. Support legs hold the trailer upright when parked, while the front bulkhead and paired stanchions define the loading zones clearly for a purposeful finished look.

RC truck accessories

1:14 3-Chamber Taillight PCB, RC lighting set

€80.99

Compact rear lighting adds a sharper scale finish to 1:14 vehicle builds, and this 3-chamber taillight PCB set brings that detail into a small round format. With dimensions of 11 x 7.5 mm, the units suit model bodies and rear sections where lighting needs to stay visually balanced instead of overpowering the build. The PCB layout combines 3 light functions in each taillight: rear light, indicator and brake light. That function mix supports more lifelike signalling on trucks, trailers and custom conversions, while the round housing shape fits classic rear-end styling on many commercial vehicle projects. The set is designed for an input voltage of 7.2-12 V DC, making it suitable for RC electrical systems within that range. For model-building enthusiasts, this adds a focused electronics upgrade that contributes visible function as well as scale character. Installed on a 1:14 rig, the taillights help complete the rear view during workshop builds, restoration-style projects or detailed road-going truck scenes. The set is not compatible with TAMIYA MFC-01/03, so it is best matched with other suitable lighting layouts and custom electronics setups.

Models & trailers

1:14 3Axle Trailer Chassis Ver.III, trailer

€389.99

The 1:14 3Axle Trailer Chassis Ver.III captures the look of a heavy road trailer in a format shaped for model-building enthusiasts. Its laser-cut steel construction uses 3 mm and 1 mm sections, creating a rigid base chassis that suits custom builds and gives larger trailer bodies a defined structural foundation. The 3-axle layout brings the long proportions of a transport trailer into a scale setup that looks convincing behind a truck tractor. A new trailer suspension system is part of the chassis design, and the included +8 mm elevation option allows the running height to be adapted to the planned structure above. Wide chromed wheels with ball bearings and wide tyres underline the technical look while supporting smooth rolling movement. At the rear, an aluminium bumper with 7-section taillights adds another recognisable truck detail. The steel spare wheel holder with spare wheel extends the workshop-style equipment, while the semi-circular mudguards shape the wheel area with a clean trailer silhouette. As a basic trailer chassis for individual structures, this version leaves room for flatbed, transport or specialist body concepts built around the frame. On a shelf, in a workshop setting or coupled to a matching 1:14 tractor unit, the long red chassis and detailed under-run protection create a strong heavy-haul presence.

RC truck accessories

1:14 4-in-1 LED Distrib.Board, model accessory

€9.99

Lighting details often define the final character of a scale build, and this 1:14 4-in-1 LED Distrib.Board is made to bring order to that stage of the setup. With 10 outputs on one board, it creates a central connection point for several LED positions within a 1:14 model and supports a tidier internal layout than separate loose branches. The board is designed as a model accessory in the Carson Modelsport range and focuses on the practical side of adding electronics to a build. Its 4-in-1 distribution concept helps separate and organise multiple light connections when a cab, body or chassis carries more than one lighting point. That makes it useful for projects where front, rear or additional marker lights need a defined place in the wiring plan. The compact board format also suits hobby work where available installation space inside a scale model is limited and every connection needs a clear route. In workshop use, the board fits naturally into the finishing phase of a 1:14 build or an upgrade of an existing model. Minimum age 14 years is stated for this accessory, matching hobby projects that combine scale detailing with electronic equipment.

Additional accessories

1:14 Box Body Conversion Kit, model kit

€399.99

This 1:14 box body conversion kit reshapes the TAMIYA Volvo FH16 timber truck 300056360 into an articulated truck with a closed cargo body. CNC-milled aluminium parts form the main box structure, while the combination of metal sections and panelled surfaces gives the finished build a purposeful commercial-truck character. A sheet steel subframe, laser cut and CNC bent, is included for mounting on the chassis and creates the structural link between the conversion and the base vehicle. The side sections use screwed plastic panels in a sandwich layout, which adds visible layering to the bodywork instead of a plain flat-sided shell. At the rear, the loading doors are carried on aluminium hinges with a 270° opening angle, allowing the opening mechanism to be shown clearly on the completed model. Magnetic locking keeps the doors closed when the body is in running or display condition. The assembled body measures 545 x 195 x 195 mm and weighs 3,200 g. As a model kit, this conversion suits hobby builds that focus on reworking an existing truck into a different transport configuration. The box body changes the visual character of the Volvo FH16 from timber hauler to enclosed freight carrier and adds a substantial new body section for workshop assembly and finishing.

RC truck accessories

1:14 Chrome Bumper MB 1838/1850, truck part

€12.49

Classic truck styling often comes down to the front details, and this 1:14 Chrome Bumper MB 1838/1850 adds a bright plated accent to compatible model builds. Designed as an accessory for Mercedes Benz truck models 56305 and 56307 from Tamiya, it brings the specified MB 1838/1850 look to the front section in a format matched to 1:14 scale projects. The bumper is made from chromed material and focuses on exterior appearance rather than a generic replacement look. Its shaped front profile and integrated mounting points are intended for the named compatible truck models, which keeps the fitment use clearly defined in the product data. The included fixing hardware consists of 2 black screws, giving the set the essential parts needed for installation. As a model accessory in the Models Supplies range, it suits detail-focused truck projects where the front end finish plays a visible role in the overall build. On a workshop bench, the plated surface adds contrast against painted cab parts and darker chassis components. In a display setting or as part of an active RC truck build, the bumper helps complete the characteristic road-truck appearance associated with the MB 1838/1850 designation.

RC chassis & attachments

1:14 Clearance Lights, model accessory, 2 pcs

€11.49

Marker lights are a small detail with a big visual role on scale trucks, and this 1:14 clearance light set brings that road-going look into a model build with red and amber lenses. The set contains 2 pieces and is listed as a model accessory for hobby use. Its compact format suits detailing work where edge markers help define the outline of a cab, body or trailer in scale form. The red and amber colour combination follows the stated design and creates a clearer visual break between body panels and fitted trim. As a separate accessory, the set can support a fresh build, a repair, or the replacement of existing marker parts where the original look needs to be restored. The 1:14 scale keeps the proportions aligned with matching model projects rather than forcing an oversized lighting detail into the build. On the bench, the set fits naturally into finishing stages where small exterior parts shape the final appearance. In display use, the coloured markers add another layer of realism to trucks and trailers that rely on visible body details rather than large mechanical changes alone.

RC truck accessories

1:14 Clearance Lights, model accessory, 2pcs

€11.49

Marker lights are a small detail with a strong effect on the finished look of a scale vehicle, and this 1:14 clearance light set brings that effect into model builds with a red and white 2-piece layout. The compact format suits focused detailing work on truck and trailer bodies where visible light points help define the lines of the model. The set is listed as a model accessory and is aimed at hobbyists from 14 years. Red and white light elements open up classic placement options on body edges, upper sections or rearward areas, depending on the build concept and the styling of the vehicle. Because the pack contains 2 pieces, the set works well for selective upgrades rather than broad full-body outfitting. That makes it a useful choice for custom projects, replacement work or finishing touches on a scale body that still needs clearly placed marker-light details. On the workbench, the accessory can be integrated into truck, trailer or other 1:14 modelling projects where small exterior parts shape the overall impression. In display use or during driving sessions, the added light housings help the bodywork read with more scale definition and a more complete road-going look.

RC truck accessories

1:14 Day Running Light Actros 2/3 Axle

€65.99

The MB Actros remains one of the defining shapes in modern long-haul trucking, and this 1:14 daytime running light set brings that road-going character into a scale build with a model-specific front lighting detail. Made for MB Actros 2/3 Axle models, the set focuses on the visual signature at the front end and adds a cleaner, more technical look to the truck body. The accessory is designed as a paired lighting set with wired left and right units, matching the mirrored layout needed for the vehicle front. Its 7.2 to 12 V/DC input range gives clear electrical guidance for integration into compatible RC truck systems. The compact housings are shaped for installation as dedicated light components rather than as generic decoration, which makes the set especially relevant for builders refining the appearance of an existing model or replacing front lighting parts with the correct format. On a workshop bench, during a rebuild, or as part of a scale detailing session, this lighting set adds a focused upgrade to the MB Actros 2/3 Axle platform. It suits display-oriented finishing as well as active RC truck projects where the front-end layout matters as much as the driving setup.

RC truck accessories

1:14 Draw Tube Pole Trailer, model accessory

€89.99

This 1:14 Draw Tube Pole Trailer accessory set brings a functional trailer detail into model-building projects with a long cylindrical draw tube, a rectangular silver housing section and an angled mounting plate with 4 round holes and 2 elongated slots. The layout reads as a dedicated add-on for scale truck or trailer work, with each part focused on mounting, alignment and visible structure rather than decoration alone. Alongside the main tube section, the set includes 2 small silver detail parts, a black bracket and a bag of black and silver screws for the fitting work. The combination of slotted and round mounting points supports careful positioning during assembly, while the separate hardware keeps the installation tied to the mechanical character of the build. A red transparent 2-part light piece and a clear lens frame extend the set beyond the structural section, adding a realistic rear-end detail that complements the metallic-looking components. 14 Years is the stated age marking. On a workshop bench, the parts suit upgrade, replacement or custom trailer projects where a scale-correct extension section matters as much as the finished look. Assembly time is stated in minutes, and batteries are not included.

Models & trailers

1:14 Dump Trailer 2/3 Axle, model kit

€619.99

Built for model truck scenes with real working character, this 1:14 dump trailer model kit brings the look of a construction-site semi-trailer into a detailed three-axle format. The combination of a CNC-milled aluminium chassis, reinforced PVC basin and back wall, and a lightened licence plate mount gives the trailer a technical, workshop-style finish that suits display builds and active driving alike. The running gear uses GFK suspension with horizontal rods, 12 ball-bearings, 6 wide rims and 6 wide tyres with a width of 25 mm and an outer diameter of 82 mm. Air-spring dummies with screw springs add another layer of scale detail to the undercarriage, while plastic fenders with mounts frame the wheel setup cleanly. The aluminium underbody protection and the CNC-milled support construction continue the metal-focused build, and the mechanically adjustable trailer supports add a functional detail at standstill. With a length of 700 mm, width of 185 mm, height of 235 mm and a weight of 4,600 g, the trailer has substantial presence in a 1:14 truck setup. For unloading scenes, the basin can be equipped with a separately available dump mechanism. A spindle drive, motor, battery and switch are required separately. Once fitted, the raised basin and automatic rear locking create a convincing loading and unloading sequence for sand, gravel or stone in construction layouts, quarry scenes or truck meeting displays.

Models & trailers

1:14 Fliegl Stone Master, tipper trailer

€749.99

Current half-pipe tippers are defined by fast unloading and a hard-working silhouette, and the 1:14 Fliegl Stone Master brings that character into a detailed 3-axle trailer kit. The licensed model combines a steel chassis frame with a steel tipper body and rear wall, creating a substantial build with the long, purposeful proportions of a site trailer. The chassis uses laser-cut and laser-welded 1 mm and 3 mm steel parts, while the tipper and hatch door are formed from 2 mm steel with a CNC-bent profile. Across the running gear, 12 ball bearings sit inside the 6 wheel assemblies for smooth rolling action. The trailer suspension is detailed with air spring dummies, and the rear section carries a 7-section taillight layout, a licence plate bracket and a square steel rear underride guard. Semi-circular mudguards, a king pin, an ABS operating platform and a hydraulic cylinder dummy add further scale detail without crowding the lines of the body. The 7-section rear light cluster can be electrically retrofitted. With dimensions of 700 x 185 x 250 mm and a load figure of up to 10 kg, the trailer has the size and carrying capacity to suit construction layouts, transport scenes and scale hauling setups. The body can be tipped and unloaded with the separately required tipping mechanism. A spindle drive, motor, battery and switch are required separately.  Warning! Not suitable for children under 14 years.

Models & trailers

1:14 Goldhofer TU4, lowloader trailer, 4-axle

€694.99

Heavy-haul lowloaders are built to move machinery that sits too tall or too heavy for a standard trailer, and the Goldhofer TU4 captures that purpose in a long 1:14 scale platform with a distinctly low deck and 4-axle layout. This kit uses laser-cut steel sheet parts to create the frame and structure, giving the model a technical build with the look of a real transport trailer. The deck is finished with wood supports that break up the steel construction with a realistic loading surface, while 16 ball-bearing wheels add a dense multi-axle stance under the chassis. At the rear, the support can be adjusted manually, and the one-piece ramps connect through a hinged mechanism that allows different loading positions. The underframe includes spacers, semicircular fenders and a pivoting bogie arrangement, adding more mechanical detail during assembly than a simple display trailer. Decals are included for markings and finishing touches, so the completed model carries the visual character of a working lowloader rather than a plain platform. Coupled behind a matching 1:14 tractor unit, the trailer suits workshop display, transport dioramas and scale loading scenes with construction or agricultural vehicles. Age 14 Years. Assembly instructions are included.  Warning! Not suitable for children under 14 years.

RC truck accessories

1:14 Lift Axle, conversion kit, trailer upgrade

€99.99

A lift axle is a defining detail on many full-size trailers, and this 1:14 conversion kit brings that function into a scale workshop project for CARSON 3-axle trailers of the II and III generation. Built for one trailer axle with dummy air suspension, the set converts it into a working lift system with a clearly visible axle movement of about 6 mm. The mechanism is driven by a digital servo and uses an aluminum servo mount, an aluminum servo horn, new mounting brackets, air bellows and mounts, plus a steel lift mechanism to create the lifting action. Mounting hardware is included for the installation. A suitable servo with at least 10 kg torque is required separately; comparable dimensions are 40 x 20 x 38 mm. The kit is compatible with Fliegl Megarunner, Stake trailer III, Flatbed trailer III, Trailer chassis III, Building materials trailer III, Box trailer III, and all 2nd generation trailers. Installation in tipper models is not possible. On a finished trailer, the raised axle changes the stance in a way that looks closer to a working road-going combination. In the workshop phase, the conversion adds a focused mechanical upgrade that suits model-building enthusiasts who enjoy functional trailer details as much as the final appearance.

RC truck accessories

1:14 Metal Front Axle, model part, steering

€19.99

A front axle defines both the stance and the steering layout of a scale truck build, and this 1:14 metal front axle with steering linkage brings those two core elements together in one dedicated model part. The metal construction gives the assembly a clearly specified material base for workshop use, while the included linkage ties the axle directly to the steering function named in the designation. Within a 1:14 build, a front axle is more than a visual detail: it is the component group that shapes how the front end is assembled and how the steering hardware is organised. This version is supplied as a front axle with steering linkage rather than as an isolated single piece, which helps keep the relevant steering section together for replacement or planned parts work. The designation identifies it as a model supply within the models and accessories range, making it a focused choice for maintenance benches, rebuild projects or scale-oriented truck assemblies. The age marking is 14 Years. Whether the task is replacing a worn front-end assembly, preparing a fresh chassis project or refining a detailed 1:14 vehicle, this axle fits naturally into hands-on hobby work. It suits model-building enthusiasts who value clearly defined components and a steering assembly that is named upfront in the specification.

RC truck accessories

1:14 MFC-TLS IR Low Loader, control unit

€84.99

Built for 1:14 truck modelling, the MFC-TLS IR Low Loader control unit extends TAMIYA MFC-03/01 with infrared signal transfer to a matching trailer setup. The module sends lighting and auxiliary commands from the tractor unit to the trailer, creating a clean functional link for low loader combinations with steerable axles. Power is supplied via the receiver at 5-7.4 V/DC, so the module integrates into an existing radio-controlled electronics layout without a separate power source stated in the data. Rear light circuit boards for 3-chamber or 6-chamber taillights connect through screw terminals, and each of the 7 outputs supports loads of up to 500 mA. That layout also leaves room for additional lamps such as marker lights, roof lights or wind deflector lights, which are switched through the parking light function. The package contents include the MFC IR transmitter module, an IR transmitting diode and a 5-pin cable set. In a detailed truck and trailer build, the unit supports coordinated light behaviour and extra driven functions across the combination. The control paths also cover steering-related trailer functions, making it suitable for low loader setups where steerable axles add a more involved operating sequence. Recommended age: 14 years. The TLS low loader control unit 500907712 is optionally required for the trailer.

RC truck accessories

1:14 Scania 770 Roof Lights, model accessory

€16.49

The Scania 770 stands out on the road with its tall cab format and strong front-end presence, and this 1:14 roof light board brings that character into a scale truck build with a focused lighting detail. Designed as a model accessory, it places 5 LED roof lights across the upper cab area to create a more defined silhouette on the finished Scania 770. The one-piece board format groups the 5 lights into a single roof-mounted assembly, which helps keep the layout consistent across the cab line. As a 1:14 accessory, it is shaped for scale modelling work where body styling and truck-specific detailing matter as much as the main chassis. The LED configuration adds a technical accent to the upper section of the model and gives the roof area a clearer visual structure than an unadorned cab top. The Scania 770 reference keeps the styling tied to a named truck subject rather than a generic lighting add-on. On the bench, the light board fits naturally into a detailed truck project alongside cab finishing and exterior upgrades. In display use or during scale driving sessions, the 5-light arrangement gives the model a more distinctive roofline and a stronger long-haul truck character.

RC truck accessories

1:14 Scania 770S Front PCB, truck lighting

€189.99

Modern long-haul trucks rely on their front light signature as much as on grille shape, and the Scania 770S is one of the clearest examples of that design language. This 1:14 front PCB lighting set translates that look into a dedicated lamp assembly for the TAMIYA Scania 770S, combining reflector detailing with functional illumination for a more authentic scale finish. The set is built around 2 matching front light modules with integrated wiring and PCB-based electronics. Each housing contains 16 LEDs, arranged to reproduce the reflector structure with a more realistic visual depth than a plain lamp insert. The lighting functions include daytime running light and side position light, adding separate illuminated zones that sharpen the truck's front profile. The specified input range of 7.2 to 12 V DC suits RC truck electrical systems in this class and gives clear compatibility guidance for installation planning. Mounted on the model, the lamp units bring more definition to the front corners, whether the truck is standing in a workshop-style display or running on an indoor course. For 14 Years and up, this accessory adds a technical finishing step that suits hobby builds focused on scale detail and working light functions.

RC truck accessories

1:14 Scania 770S LED Board Side, model part

€31.99

This 1:14 side LED board set is made for Scania 770S model builds and brings a defined lighting component to the truck's side sections. With 2 matching boards in the set, the layout suits symmetrical installation and gives the model a more complete illuminated appearance. The designation names a 3A specification, adding a concrete electrical reference for integration into a compatible lighting setup. As a dedicated model accessory rather than a complete vehicle, the set focuses on one specific area of the build and supports more detailed finishing work on a Scania 770S project. The side board format helps separate this component from front or rear lighting elements and makes it easier to plan placement within a larger 1:14 truck configuration. In a workshop setting, the pair can be fitted during a fresh build or used to refine an existing Scania 770S model with added side illumination. The clearly defined scale and vehicle reference also make the set a focused choice for hobbyists working on truck detailing with matching 1:14 components.

RC truck accessories

1:14 Scania 770s LED Board, model accessory

€32.49

The Scania 770 S belongs to the latest generation of long-haul trucks, known for its bold front design and strong road presence. This 1:14 LED board is made for that look in model form, adding a defined lighting element to the front area of a Scania 770s build. The accessory is specified as a 4+3 front LED board, giving model-building enthusiasts a clear layout for cab detailing rather than a generic light part. In a 1:14 truck project, details at the grille and roofline shape the whole character of the finished replica, and this board focuses attention on that upper front section. The Scania 770s designation keeps the part tied to a specific subject, which matters when a build is planned around the lines and proportions of one truck model. As a model accessory rather than a complete vehicle, it suits hobby benches where selected parts are added step by step to develop a more individual finish. Whether the goal is a shelf display, a show-style truck replica, or a running 1:14 build with extra visual definition at the front, this LED board adds a distinct custom element. The compact format also makes it a useful choice for targeted upgrades where one visible detail can change the overall impression of the cab.

RC truck accessories

1:14 Scania 770S Positionlight Set, LED kit

€85.99

The Scania 770S is known for its bold front-end presence, and this 1:14 position light set translates that character into a dedicated LED upgrade for scale truck builds. With 21 LEDs and support for 7.2 V and 12 V systems, the set is aimed at model-building enthusiasts who want to add a more intricate lighting layout to a Scania 770S project. The wiring harnesses are arranged for several mounting points around the truck body, with light outputs assigned to roof lamps, side skirt position lights and multiple front lighting locations. Alongside the roof position lamps with high beam function, the set also covers 5 lightbar pods, a bumper lightbar and an auxiliary light in the radiator grille. This spreads the illumination across upper, central and lower sections of the cab, giving the model a more structured and realistic light distribution once installed. The prewired LED lines also support neat routing through a detailed truck build where cable placement matters as much as the finished effect. On a display shelf, in a workshop build, or during powered running sessions, the set adds visible definition to the Scania 770S bodywork and helps separate the truck's key styling zones through light placement. The set is not compatible with TAMIYA MFC-01/03.

RC truck accessories

1:14 Steel Drive Shaft 47-57 mm, model part

€17.49

A steel drive shaft in 1:14 scale format brings a core drivetrain component to compatible model vehicle builds. The stated 47-57 mm length range defines the working span clearly, making this part relevant wherever that exact distance is needed between connected drivetrain points. As a model accessory in the Models & Accessories range, this shaft is aimed at repair, replacement, or planned drivetrain setup work rather than decorative use. The steel construction places the focus on a metal transmission part for hobby applications, and the compact 47 mm to 57 mm specification gives a concrete reference when matching an existing assembly. With a minimum age marking of 14 years, the part sits in a hobby context shaped by model-building and technical maintenance. The designation itself keeps the function straightforward: drive shaft, steel construction, 1:14 scale reference, and a defined length window. On the workbench, this kind of spare part supports routine servicing of compatible RC models, whether an existing shaft is being replaced or a drivetrain layout is being completed with the required size. It also fits neatly into a stocked parts assortment for ongoing maintenance of 1:14 vehicle projects.

RC truck accessories

1:14 Steel Drive Shaft, model part, 40-45 mm

€17.49

This 1:14 steel drive shaft is a compact model part for driveline setups that need a stated length range of 40-45 mm. The steel construction and scale-specific designation give model-building enthusiasts a clear starting point for matching the part to an existing build or replacement task. Within a model workshop, a drive shaft sits at the heart of mechanical power transfer, linking rotating components in the drivetrain. Here, the key data stays focused and usable: 1:14 scale reference, steel material, and a 40-45 mm size range. That makes the part easy to place in projects where a short shaft section is required and where the dimensions need to be checked against the installed layout. The concise specification also suits spare-parts planning, because the material and size can be identified quickly without sorting through broader vehicle claims that the data does not state. Whether the task is replacing a worn shaft in a running model or selecting parts for a fresh chassis setup, this component brings the essential information into one straightforward format. The 40-45 mm range supports comparison against existing hardware, while the steel build keeps the focus on a concrete, named material for hobby use.

RC truck accessories

1:14 Steel Drive Shaft, model part, 75-100 mm

€17.49

This 1:14 steel drive shaft is a dedicated drivetrain part for model assemblies that need an adjustable connection length from 75 to 100 mm. The steel shaft brings a clear mechanical role into the build, linking compatible drivetrain points within that stated span and supporting a precise, component-led setup. In a 1:14 model context, the 75 to 100 mm format gives room for installations where the distance between connected parts is not fixed to a single length. That makes the shaft relevant for replacement work as well as for fresh assemblies built around matching dimensions. The steel construction keeps the focus on the part's intended function as a drivetrain link rather than a decorative add-on. With the age marking of 14 Years, the part sits in a hobby-focused model range shaped around detailed builds and technical component choices. Whether used to replace a worn drivetrain link or to complete a compatible 1:14 project, the shaft fits naturally into workshop-style model building sessions. It suits hobby benches where measured component selection, matching dimensions and drivetrain layout all matter to the finished assembly.

RC truck accessories

1:14 Steering Axle, truck accessory, steel

€99.99

In 1:14 truck building, the steering axle shapes how the whole front end responds on the road. This pre-assembled front axle combines a hardened steel center section, hardened steel steering knuckles and aluminum linkages into a ready-to-install unit for TAMIYA truck models. The axle body forms the core of the assembly, while double plain-bearing-mounted steering knuckles support precise steering movement at each side. A steel tie rod with left- and right-hand threads allows fine tracking adjustment directly at the linkage, which helps dial in the front end with more control during setup. Backlash-free M3 ball joints transfer the steering motion through the system with accurate, direct action. The combination of steel load-bearing parts and aluminum linkages gives the assembly a focused mechanical layout built around steering precision. Installed on compatible TAMIYA truck chassis, the axle suits fresh builds, rebuilds and targeted front-end upgrades where exact steering response matters. The ready-for-installation format also keeps workshop time focused on fitting and setup rather than on assembling the axle itself.

RC truck accessories

1:14 Strobe Light orange, model accessory, 2 pcs

€45.99

Amber warning lights are a familiar detail on working trucks, and this 1:14 strobe light set brings that look into a model build with 2 compact light units. Each housing measures 11.5 x 4.5 x 2.5 mm, giving the set a small footprint that suits scale installations where lighting needs to stay in proportion to the bodywork. The lights are designed for 7.2-12 V DC input and come as orange strobe units for model electrics in that voltage range. The image shows slim silver housings with attached wires, a layout that supports installation on body sections, roof areas or accessory bars where a separate warning-light detail is needed. Compatibility with the 500907633 beacon light bar set makes this set a focused extension for existing 1:14 truck lighting projects rather than a generic decoration. Used on a show truck, service vehicle or detailed working rig, the 2 strobe lights add a distinct visual accent that sharpens the scale appearance. In custom builds, restorations or lighting upgrades, the compact format leaves room for precise placement while the amber colour reinforces the look of real commercial vehicle warning equipment.

Basic accessories

1:14 Towing bar Low loader, model accessory

€26.99

This 1:14 towing bar for the Low loader adds a defined structural part to scale model work, with a black moulded form that follows an A-shaped layout and integrates reinforcing ribs across the frame. The geometry shown in the part itself points to a mechanical connection role, with 1 circular mounting eye on one end and 2 cylindrical mounting points on the other for placement in the intended assembly. As a dedicated model accessory in the Models & Accessories range, the part suits replacement work, maintenance tasks or the completion of an existing 1:14 Low loader setup. The ribbed structure gives the component its formed profile, while the open triangular shape keeps the connection points clearly accessible during fitting. For hobby projects where the correct shape matters, a scale-specific part like this helps keep the model configuration consistent with the intended layout. The 14 Years age marking places the towing bar in the hobby segment rather than in early-play ranges. It fits naturally into bench work focused on repair, parts management and scale vehicle upkeep, whether the aim is to replace a worn component or keep a matching spare ready for later use.

Basic accessories

1:14 Towing Bar Trailer, model accessory

€26.99

The 1:14 Towing Bar Trailer is a model accessory with a clear utility-focused shape for scale vehicle and trailer projects. Its black moulded form combines a long drawbar arm, a circular eyelet and a broad triangular centre panel, creating a part that reads immediately as a towing or linkage component within a larger assembly. The centre section carries a raised diamond-plate texture that gives the surface an industrial look suited to working vehicle scenes and technical model layouts. Along one side, small mounting tabs with holes add further fastening points, while the two extending arms end in compact connector joints for attachment within a compatible structure. This combination of eyelet, tabs and connector ends supports use as a linking, hinging or stabilising element, depending on the model setup described by the builder's own project. The 1:14 scale keeps the part aligned with matching scale builds where proportion matters. In workshop-style rebuilds, replacement jobs or custom trailer configurations, this accessory brings a distinct mechanical detail to the assembly. It suits hobby benches where individual components are selected for fit, function and scale appearance rather than as stand-alone display pieces.

Models & trailers

1:14 Trailer Chassis 20/40ft.Cont., trailer

€399.99

Built around a CNC-milled aluminium frame with a black anodised finish, this 1:14 Trailer Chassis 20/40ft.Cont. brings container transport into a detailed scale format with a long 915 mm silhouette and a purposeful commercial-vehicle look. The 190 mm width and 140 mm height give the chassis a low, stretched profile that sits naturally behind a matching tractor unit in workshop, display or driving scenes. The 3-axle layout is paired with swing axle suspension and flat springs, so the undercarriage carries visible mechanical depth as well as articulated movement. Wide-base tyres with foam inserts add body to the running gear, while chrome-plated rims sharpen the road-going finish. Mechanical seat posts extend the functional trailer character beyond surface styling, and the changeable container fastening allows the chassis to be set up for 20 ft or 40 ft container formats. Age marking: 14 years. Behind a tractor unit, the long frame and multi-axle arrangement create the look of a working freight combination with clear transport focus rather than a generic road trailer. The chassis suits model-building enthusiasts who enjoy realistic commercial vehicle themes, detailed underframe construction and scale scenes centred on loading, hauling and depot movement.

Basic accessories

1:14 Trailersus. 8mm Lift, trailer axle parts

€29.99

A 1:14 trailer model gains a more technical underbody look with this Trailersus. set and its 8 mm lift layout. Created for retrofitting existing trailer axles with dummy air springs, the set brings the suspension area closer to the visual character often sought in detailed truck and trailer builds. The package contains the necessary moulded parts and 2 air bellows for the conversion. It is intended for use with dummy air springs 500907069, while the metal parts and the assembly material are reused from the existing axle. That setup keeps the focus on the suspension components that change the appearance of the axle assembly, rather than replacing the complete axle hardware. The black moulded parts suit workshop-style builds, restoration projects, and scale trailer customisation where the axle zone is meant to look more complete. One set is required for each trailer axle, which helps when planning a single retrofit or equipping several axles on a longer trailer. The 14 Years marking is stated in the product data. In a display build or a running truck-and-trailer combination, the conversion adds a more model-focused finish to the area beneath the trailer body.

RC truck accessories

1:14 UNI-TLS IR, transmitter unit, low loader

€84.99

Heavy-haul trailer functions become far more precise with the 1:14 UNI-TLS IR transmitter unit, built to connect an existing lighting system to the CARSON TLS low-loader control setup. The module sends both lighting and auxiliary commands to the trailer via infrared, creating a clean control link for complex low-loader operation. Designed for third-party use, the unit expands a 1:14 electronics layout with a focused set of control options for articulated transport models. The infrared transmitting diode forms the signal bridge to the trailer control unit 500907712, which is required separately for trailer control. Alongside standard light commands, the system supports additional switching tasks for functions such as a gooseneck section, electric supports, ramp drive or steerable trailer axles. Operating voltage is 5-7.4 V DC, and power is supplied directly via the receiver. Scope of delivery includes the UNI transmitter module, IR transmitting diode, 10-pin cable set and instructions. In a workshop-style build or an active driving layout, the module suits model hauliers who want trailer lighting and moving low-loader functions to respond through one coordinated infrared link. It fits especially well into detailed truck and trailer combinations where realistic control of transport equipment matters as much as the tractor unit itself.

RC truck accessories

1:14 Warning Signs LED TLS, trailer accessory

€54.99

Heavy haulage details make the difference on a scale build, and these 1:14 warning signs bring that look into the trailer setup with illuminated red and white SMD LEDs. The set contains 4 warning signs ready to connect, adding a functional lighting element that suits low-loader scenes and transport-focused model layouts. The pre-wired power circuit board keeps the electrical side straightforward and is designed for direct connection to the TLS low-loader control unit 500907712. Installation uses the existing mounting points on the CARSON gooseneck low-bed trailer 500907700, which keeps the fit aligned with the intended trailer platform. Each sign measures 21 x 21 mm with a width of 71 mm, giving the assembly a compact scale presence. The extendable construction can be moved in or out by loosening the screws, so the sign position can be adapted to the width of the load. Mounted on a low-bed trailer, the illuminated signs add a convincing finishing touch to heavy transport combinations in workshop builds, display setups, and driving sessions. The 5 V/DC operating voltage matches the stated electrical specification for integration into the TLS system.